Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi, I have a question on USB performance of nRF52840. I have Rigado BMD-340(s) and I have to verify the maximum data rate supported on USB interface. Its says 12 mbps in the...
Hi
There are two PCA10090 DK boards. Each one had its own iBASIS card.
Previously, I registered these two in nRF Connect for Cloud. DK board A with SIM card A.
DK board...
I have ordered some PCBs which have I2C lines on P0.08 and P0.09 and have been trying to test using the Dev Kit and for some reason, I can't get any traffic out of these pins...
Hello. I want to add OTA DFU feature to my device, based on nRF52810. I already met problem with not enough space on this chip, but it was solved, so I hope it possible to...
nRF52832 will restart accidentally, I have checked code, but I haven't fixed it so far;
Because restart is random, it is hard to reappear;
my question is
1, How do I...
Hi Sir,
My project need LESC & AES-CMAC function, then I enabled below CONFIG in sdk_config.h :
NRF_CRYPTO_BACKEND_MBEDTLS_ENABLED
NRF_CRYPTO_BACKEND_MBEDTLS_ECC_SECP256R1_ENABLED...
Hi,
So I am trying to configure the stdout console to use UART1 by default. Using the NrfConnect menuconfig in Segger emStudio I can set it to use UART1 with the following...
Hello !
I have read in DevZone, but still not sure regarding nRF52832 .
For nRF52832 and page size 4k, and regarding only writing zero-bits.
Can I in same page perform...
Hi team,
Here is the previous ticket
https://devzone.nordicsemi.com/support/234693
One of my customer TMC is using our nRF52810 in a BLE key project for central role...
When in dfu mode (with usb dfu enabled) if we jump to application via "
nrf_bootloader_app_start" there seems to be an issue where the firmware locks up and doesn't start...
Hello
my setup is a nrf52840, the sdk15.3, Softdevice s140.
is there a possibility, maybe with freertos, to to run two seperate applications like two threads.
In the...
Hi,
I'm trying to implement a slow timer which is supposed to be triggered about every 30 minutes or even less frequent, but I'm kind of clueless how to solve this issue...
from which antenna these values were derived resp. measured? e.g. there is a pcb antenna and a hirose u.fl connector available on pca10040... examples/ble_peripheral/ble_app_eddystone...
