Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi all,
I am currently working on a personal project with hundreds of nodes. I have created a device with remote provisioning models (server and client). In my network...
I'm encountering an issue while trying to use the CAF LED module with the nPM1300 PMIC. Despite configuring the Device Tree, prj.conf, and led_state_def.h, I'm still getting...
I have an app where I'm using the AP and STA mode of the 7002. I'm running on a nrf5340.
*** Booting nRF Connect SDK v3.5.99-ncs1-1-1-g6dc48c918694 *** [00:00:12.620,269...
Hey, everyone. I am currently working with NRF9160, NCS V1.3.0, developing code for an application that requires periodically storing important information in flash, and send...
Hi I have a mbed application, which runs on a PSOC6 MCU, i am going to be using a fanstel BC832 (which is based of NRF52832)BT module for RF-communication. To verify that...
I would like to confirm if my understanding is correct regarding calculating the average current consumption using the PPK2.
As shown in the image, the Selection Average...
I can't find any mention about MU-MIMO in the datasheet. Does the nRF7002 support MU-MIMO TX and RX?
I cannot find any details of if support is mandatory for a 802.11ax...
Hello,
I need to implement Find My Device for nRF52833.
From Sample I could find "samples/bluetooth/fast_pair/Locator Tag" example. I tried to go through it. but I could...
Hi,
This string is defined by "CONFIG_BT_DIS_FW_REV_STR". Is there any API that can modify it?
Currently version management is done through VERSION files, but its display...
Hi,
We are using the nrf52833 for development.
The first version of the program can connect to the discovery service normally. But we need to add some new features. And...
When I recently tried to write a Gazell project using the nRF Connect SDK, I found that many files referenced the `nrf_gzll.h` file, but I did not find it in the nRF Connect...
Hello,
I've been playing with an nRF54L15 PDK, specifically with the sid_end_device sample. I was having a lot of trouble getting the device to register/connect to Sidewalk...
Lesson 8 of "nRF Connect SDK Intermediate" DevAcademy course deals with Bootloaders. I've successfully done the exercise of updating firmware using the off-the-shelf mcuboot...
hi,i wanna read the imu sensor lsm6ds3 on board of nrf52840 based Xiao BLE Sense
so i used the code in samples /sensor/lsm6dsl
first i didn't know if i do have to create...
Hi supporter
we try to radio test for nrf7002 DK, we use ncs2.7.0 version, need to radio test for 2.4G Ble(2440 MHz) and Wifi(2440 MHz), 5G wifi(5500 MHz), need to measure...
