Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Thingy:91X V1.0.0 (multiple devices)
NCS 2.6.2, nrf53_connectivity_bridge_v2.0.1
Using the logging of the nRF9151 via the nrf53_connectivity_bridge_v2.0.1 shows on longer...
Hi, We have a network of air quality nodes based on the nrf9160 using Vodacom in South Africa. One morning all the nodes went offline and we discovered that they no longer...
Dear Nordic Technical Support,
I'm writing to report an issue I'm experiencing when trying to integrate MCUboot with a Zigbee R23 project for the nRF54L15 platform.
Issue...
Hi, I am having trouble with the connection of my mesh nodes and my Smartphone over the nRF Mesh App. After flashing my boards ( nRF - 52833, 52840, and 7002), most of the...
HI all,
I'm trying to run the USB next stack-based loopback class with Linux testusb. and only very few of them been passed and everything else been timed out.
I confirmed...
Hello,
We have nRF52832 in production on a custom board. Recently, we created a new functionality with the aim to handle flash more efficiently, and to avoid the case where...
Hi All,
Hardware Details:
nRF-SDK: 2.8
Microcontroller: nRF52840
Setup:
We have an OpenThread (OT) mesh network consisting of approximately 15 devices. All devices...
We are trying to incorporate nRF9160 to our project. In which we need both GNSS and LTE features. The solution is a tracking device so we need the GPS functionality. We have...
I am looking to figure out my current consumption with an NRF52832 chip. I have the NRF chip running at 3V using UART, SAADC, BLE and SPI. The chip is constantly reading some...
Hello, I have been trying to install nRF Connect SDK v2.9.0 for 2 days. I am currently using Linux Mint 22 Cinnamon and git version 2.43.0. When I try to install it via toolchain...
Hey Nordic Team,
I'm facing an issue while flashing the audio application on our custom PCB. The interfaces of the custom PCB pretty much match those of nRF5340 Audio DK...
Hey,
I encountered a problem with the thread viewer, where the corresponding window is empty when I'm in a debug session. Inside the build configuration I used "Optimize...
Hi all,
I am running the lsm6dso zephyr sample on my nrf52833 dev kit. I am unable to set the sampling frequency. I get this error after flashing:
This is my overlay...
