Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
I'm using the nrf52840DK to power our external target board. I've noticed that the VDD level in a nrf52840DK is 3V, and not 3V3. This might be enough to throw our board off...
We have code that puts the HW to sleep. On a nRF52833. The pseudo code would be something like this - <shutdown SD, stop freertos scheduler, stop interrupts, power down all...
my code base is samples/bluetooth/central_hids and samples/bluetooth/peripheral_hids_keyboard, NCS 2.6.1
Central
diff --git a/prj.conf b/prj.conf index c85e49d..0543efe...
Hi.
I try to build the nrf_audio sample as BIS headset with enabled FOTA and NCS2.7.0 and get the following link error for the ipc_radio image:
FAILED: zephyr/zephyr_pre0...
I need to use 9160 to drive the Lis2dw12 accelerometer for ST. I found some settings related to this accelerometer in NCS, but I couldn't use it after adding it in IIC, and...
Hello,
is there any technical reason why the MPSL radio notification API has been dropped somewhere before NCS 2.6?
Our application needs information about radio notifications...
Hi, I'm looking into a design based on the npm1300 and nrf5340 for a battery-powered wearable device.
We would like to use two buttons (A and B) as the user interface with...
We have nrf52840 S140 BLE Central device that currently connects to TI based sensors. I have implemented code that can upgrade those TI sensors' firmware using the TI BLE...
In BLE Fundamentals, Lesson 3, Ex. 1 (BLE connection exercise), the nRF84020 DK board indicates a successful connection (led 2 is on + connection message in serial terminal...
Currently, I am creating a CIS-connected device using nRF5340 Audio on a homemade board.
Since the circuit configurations of the Gateway and Headset are different, I have...
I just got a fresh Win install and installed a new version of vs code (details below) and lo and behold the nrf welcome page is empty! Apparently, this was changed a while...
Hi I am looking for some advice with regards to getting a Fanstel BU840XE ( BU840XE, The longest range, Remote USB Dongle for BLE 5, Thread, Zigbee — Fanstel ) device to function...
Hi team,
I am getting secure fault after PPP started in SLM (v2.6.1) application.
here is the snapshot of the error message
Anyone having same issue and resolved please...
I am experiencing an issue with the I2C device on the nRF5340(our custom board) where it is unable to read/write to the sensor, resulting in a return value of -5.(EIO)
Details...
Hi
I'm chnaging the Secure Bootloader to an external falsh for bank1, connected with QSPI.
In the function on_data_obj_write_request is the call for nrf_dfu_flash_store...
