Hi,
I am working on internal flash nRF52832 merged with twi sensor, my sensor function will return a string . How to assign the string to the my_data.p_data . i am getting...
Developing on the nrf51822
Have working code for the nRF52840 Dongle using the pc-ble-driver therefore all Bluetooth work is done using sd_* calls. The PC provides easy...
Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello. I have read a topic about ADC calibration (gain and offset error in 0x10000024) of nRF51822 here but I can't find the document describing it. Could anyone point me...
Hi,
I am beginning to design a wearable device with motor vibration using nRF52 SDK and SoftDevice S132.
In firmware side, I have no problem to control a led on and off...
Hi
in my test bench for system validation I would like to control the system based on nRF52 via Bluetooth to speed up testting of various samples.
It seems that there...
Good day.
We recently bought the NRF52 DK and the Power Profiler Kit with the intent to log power consumption of our battery powered products. Before purchasing the products...
Hi,
I tried nrf connect and nrf hrs example. I used nrf52DK. I bonded the device, and connected with autoconnect. I turned off the nrf 52 DK, and turn on. The nrf connect...
I am using the secure bootloader with DFU, and the buttonless DFU service. I extracted these applications from the Thingy SDK v2.1.0. This works perfectly fine as long as...
Hi,
My problems are as follows:
SDK :nRF5_SDK_15.0.0_a53641a.
IDE:MDK 5.2.6
Chip:nrf52832 SPI0
External Flash :W25Q64
Now ,I can read the chip ID correctly ,but...
Hi,
Please find following source code.
After compiler by Keil 5.24.2, some code will not compiled,
I can see the situation by "enter debug mode, please find following...
Hi,
I am trying to develop a central device that would scan for devices that start with a prefix XYZ_, for example XYZ_1111, XYZ_1245,...
Is there some way to add a name...
Hi,
I am using esb function to implement my project, and I set "noack" condition to "true".
How can I know the destination address when I receive a packet?
Thank you...
I need to add ARM_MATH_CM4 to my preprocessor definitions using Segger Embedded Studio.
I know this has been dealt with in "nRF52832: How to Include the "arm_math.h" library...
We are developing a BLE device that will act as a central and send data to a peripheral. To begin with, I have used the uart central example code from SDK to set up a central...
Hi, I am trying to figure out the adc example posted by Nordic Semiconductor on Github.
https://github.com/NordicPlayground/nRF52-ADC-examples
There was two examples,...
Say I have the PWM Decoder set to NRF_PWM_STEP_TRIGGERED. If I use NRF_PWM_TASK_NEXTSTEP to step through a PWM sequence, will an event be generated for each step? I would...
Hi,
I have merged ble_app_multilink_central example and ble_app_uart_c example. and function is Ok.
Central(nRF52) can connect to HM-10(ti cc254x) and communication is...
