Developing on the nrf51822
Have working code for the nRF52840 Dongle using the pc-ble-driver therefore all Bluetooth work is done using sd_* calls. The PC provides easy...
Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hello, and thanks for all the great examples!
I've gotten the COAP transport for background DFU working on my custom hardware platform and app, however I have noticed that...
Hi,
I do have a NRF51-DK and want to use it as a external programmer. I connected it to the OUTPUT Port which worked fine, then I flashed the mbed firmware on it because...
Hello,.
I have a question about using app_usbd_cdc_acm_read and app_usbd_cdc_acm_read_any in SDK15.2.0,
I am not sure I fully understand the description in reference...
nRF52832, SDK 14.0.0, SoftDevice 132 v5.
If SoftDevice is enabled but the system is not yet advertising or connected via BLE, will SoftDevice ever wake the CPU up from...
Although redirect.c is included and printf() calls use the uart as expected, fgets() calls don't seem to be able to detect incoming characters.
This isn't critical, since...
Checking QDEC (Quadrature decoder) of nRF52832.
But, In a SAMPLEPER Register(0x508) when set to 128us(0) or 256us(1) does not occur SAMPLERDY Event.
On the other hand...
Hi,
I am working on a project running on a nRF52832, using SDK 12.3 and S130. I use Eclipse (2018-12) as my IDE.
I have followed the explanations from this tutorial :...
Hi,
I am using a nRF52832 to communicate with a ICM-20948. I've been trying to write a 16 byte packet of data and read back and verify that same data. According to the ICM...
Hi,
I am trying to communicate from STM32 Nucleo board to murata's MBN52832, using SPI, with the nordic chip being the slave. So, for this I used the SPIS example from the...
Hi,
I am trying to get the ADC up and running on the nRF9160 DK. I had a look for example code and the latest I found was here.
https://github.com/Rallare/fw-nrfconnect...
Hi, I am using N52832 to developing a producation need to implements ANCS NC. I am using sdk 15.2. And I found the connection is terminated by the apple device after the reconnect...
I am using BLE peripheral UART application from nordic SDK version 15.2.0 SoftDevice S140 PCA10056 nRF52840 Development kit on Embedded Segger studio operating system - Windows...
I am trying to design some test cases to check the LTE stability and performance.
I avoid to use the existing Nordic samples to do this as they are too complicate for the...
I am migrating an existing project to nRF5_SDK_15.3.0, and I want to know why the error occurs and how to fix it ...
1. ..\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined...
Hello to everyone.
I'm working with nRF52832 SDK (PCA 10040) and Segger Embedded Studio v4.12, in the Light_switch example for Mesh 3.10. Right now, I'm able to use the...
