Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
My setup includes 2 nRF52840 DKs, one flashed with periodic_adv_rsp and the other with periodic_sync_rsp. I copied the samples and auto-generated a build configuration for...
I cannot get Zephyr-only DFU over BLE working. Using an NRF52840DK. This is my prj.conf :
---
CONFIG_GPIO=y CONFIG_LOG=y # CONFIG_BOARD_HAS_NRF5_BOOTLOADER=n # Enable...
I am working on nrf5340dk board with 2.6.1 SDK and toolchains.
So, I took "mesh_shell" project as a starting point, then added external flash and mcuboot with simultaneous...
I would like to prepare my RAK4631 supported board file to Zephyr , but I am having problems with my JLink device, then I bought a new device but it didn´t arrive yet.
...
Hello,
i am using the nPM1300 with a nRF52840. This question is regaring the WDT in the nPM1300.
After reading the datasheet of the nPM1300 my understanding is, that event...
i have ZSWatch complete hardware by jackob and kempy and the link is provided below and using the vscode (nrf connect) to code in it in my case the debugger by segger technology...
am using the NRF52840 DK to interact with some BLE devices, and I am trying to use NRF Connect for Desktop Bluetooth Low Energy .
While the DK is correctly recognized in...
I'm, trying to use the ble_app_uart example for SDK v17.1. I can run the example correctly, but when I try to copy-paste the main code, I can't use the UART. I normally send...
Hello Support,
I was trying to get the information of services and characteristics from the peripheral after the connection is established.
With sd_ble_gattc_primary_services_discover...
Hello,
Is there a method of setting the transmit power of ISO channels using BT_HCI_OP_VS_WRITE_TX_POWER_LEVEL?
I used the connection handle of the struct bt_conn object...
Hello,
I want to use SPIS peripheral in nrf7002-DK on the net core. I cannot compile (error 'NRFX_SPIS0_INST_IDX' undeclared (first use in this function))
here is my firmware...
Hello Nordic Team,
I'm struggling with a bug on HID transfert.
My product send HID buffers with a size of 32 bytes, everything was working fine so far.
But when I...
I already did a new VSCode/nRF Connect for VSCode Extension Pack installation, but I can´t find what kind part is missed in the instalation process
In the Build and Flash...
I am programming with the nRF52840DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I simply want to toggle the 0.18 pin between...
