Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
what can be the starting Point for Bachelor Thesis involving BLE 5.0 devices to be deploy in mesh Network. How the challanges in the Thesis can be address and set as a Goal...
Note: This is related to the following issues:
- https://devzone.nordicsemi.com/f/nordic-q-a/63255/nrf9160-getting-stuck-after-cell-change
- https://devzone.nordicsemi...
Hi,
I am working on DFU-OTA sample as suggested in this link. https://devzone.nordicsemi.com/f/nordic-q-a/84766/sample-ncs-code-to-evaluate-dfu-ota-on-nrf52833 .
For nrf52833...
Hello,
I'm using a custom board and i actually have a problem that I never saw before : error 34 (0x22) GATT CONN LMP TIMEOUT.
I have send frames : I did my own custom...
I have a custom design with NRF9160. I try to use the debug output of the NRF9160 DK, but on the debug-out of the nrf91 DK it is not recognize (target Voltage is visible at...
we use nRF52833,SDK:S140,17.2,sometims,the device goes into trouble and the error code is 0x715.
here is the call stack:
/port.c:128 0x00027482 PendSV_Handler
/port...
When developing a BLE device with nRF52840, the following error occurred when importing the header file for spi communication.
ERROR ['NRF_DRV_SPI_INSTANCE_0' undeclared...
I am using FreeRTOS with FatFS/SD card. SDK is nRF5_SDK_17.0.2.
If different tasks access FatFS API in different task, is it thread-safe? i.e. Task A access file A and task...
Hi,
I'm integrating the ble_app_uart example into my project. However, the UART interrupt works a little differently than I expect. I initialized the UART with APP_UART_FIFO_INIT...
Hello
I followed the doc blew for building sample
- https://infocenter.nordicsemi.com/topic/ug_gsg_ses/UG/gsg/intro.html
- https://devzone.nordicsemi.com/nordic/nordic...
Hi,
Currently I have a NRF52832 chip that I am using in a project. The chip is inaccessible since it is inside a device -- I have been performing software updates via the...
I've mistakenly closed the case https://devzone.nordicsemi.com/f/nordic-q-a/85450/insufficientresources-error-message-while-performing-usb-dfu?ReplyFilter=Answers&ReplySortBy...
Hello,
I am referring to the ISP4520 example code .
I would like to change the I2C(TWI) pin assignments as below.
SCL:P0_07 / SDA:P0_12
But I can't find where to set...
SDK 17.1.0
nRF52840 DK central + nRF52840 peripheral device
Hello,
I'm attempting to set up reading characteristic values on the nRF52840 DK as a central from a peripheral...
hi,
We are currently having some problems erasing flash，The problem recurrence rate was 1%，the recurrence rate of specify chip problems is 100%，Here are some scenarios as...
Hi,
In secure_bootloader(SDK17.1.0) example, I want to replace the ECDSA_P256_SHA256 with ED25519, what should I do?
I tried to modify sdk_config.h, but the build didn...
I have the EV BT-840 DK and I have the AT firmware installed. With AT commands I am able to connect and send data to other BT-840DK. Right now I flip the AT command switch...
