I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
I'm using Windows and ble_app_uart example for my development.
I wanted to check log from my dongle so I'm trying to use log_backend_uart with putty.
But I couldn't get...
Hi,
I want to use a TSOP IR receiver on a custom board for sending different commands to my device through a remote controller. for example, if I use a Samsung TV controller...
I want to configure the NPM1100 to work with either rechargeable or non-rechargeable batteries (in factory).
Would it work to set mount a suitable resistor to the NTC pin...
Hi,
We are evaluating thread. And would like to build a basic demo app using a thread border router and a few sensors. We got the border router working with the coprocessor...
Hi,
I am using nrfconnect sdk with central_uart example. How to get the name of the device
advertise the BLE discovery packets? nrfconnect android app shows the name after...
Hej!
I see that the CRC block is used in the Radio under section 23.6 of nRF52832_PS_v1.4.pdf . Also, I noticed that the CRC32_ENABLED is only enabled in the bootloader...
My previous ticket is closed. I would need, but still help with the configuration of the pins. I report my last post.
Hello, I did some tests with the oscilloscope directly...
Hi,
The previous SDK would allow configuring radio notifications before the radio comms would take place.
I wonder if it is possible to get similar notifications on the...
i have a requirement to connect two nrf52833 boards to connect each other.
(1).if i turn on the Board1 should scan the bluetooth devices if any other bluetooth devices present...
I am working on a proprietary RADIO protocol on the nRF5340 device. Because I'm trying to squeeze as much throughput as possible out of the RADIO I would like to be able to...
I am developing my first BLE Server application with the nRF52832 and using VSC/nRF Connect/Zephyr ROTS. I come from a Cypress/PSOC Creator background, and am struggling a...
Hi DevZone,
I recently updated my version of SEGGER Embedded Studio for ARM to v6.20. Now, warnings that were not shown before are caught.
I want to ignore the warning...
Hi Nordic, Currently my project is using SDK 15.3. By taking a look at NCS SDK, I can see lots of features there and plan to migrate my project to NCS 1.9.0. However, since...
The NRF5340 net core crashes in sdc_hci_cmd_le_set_adv_enable() if I have CONFIG_CLOCK_CONTROL_NRF_CALIBRATION_MAX_SKIP set to 0.
To reproduce the issue, do the following...
Hi ,
I am using nrf52833dvk and nrf52832 boards, am working on application that my nrf52833 board do the firmware updation of other board i.e. nrf52832 . first time i did...
