Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, it's my 1st time using nRF Connect SDK for nRF5340. After click OK (see screenshot), I had this CMake error.
Because my previous folder contains white space (C:/Users...
I've been trying to run the FreeRTOS blink example on a custom board.
After some time (I have not yet been able to determine exactly how long - but somewhere in the range...
Hello,
I would like to use k_uptime_get, however this is returning an int64_t where I would expect an uint64_t.
While looking in the function, I see that k_uptime_get...
Hello,
We need to add secure services to our application, and I followed the guide in https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/software/posts/using...
I have downloaded the ble_app_blinky_c_pca10056_s140 hex file to the development kit with the help of the nrf_connect windows application. I have a PCA10100 development kit...
There is no 32767Hz crystal oscillator on my circuit, so the clock source of softdevice is configured as RC to ensure that the system can function normally. Now I use the...
I have successfully run a firmware in NRF52840 DK board. With NRF52840 DK ,I have tested AWS IOT BLE Nrf. Now I have also NRF52840 Dongle. Because small form factor, I would...
Hi Nordic support,
I was trying to get the Asset Tracker app running on the Thingy91 device but encountered various problems. Basically it can't get connected with the network...
Hi,everybody!
I started to connect the PCA9685 to the nRF52 DK and ran into a strange problem. When initializing the PWM module, it does not work.Initialization requires...
Hello DevZone,
I am developing on nRF5340-DK v0.11.0, with nrfx v2.2.0 running with mbed Cordio, compiled with GNU make 4.3. The end goal is to make a Bootloader for the...
Hello everybody. I need to rotate servo and check adc on potentiometer to stop it if something is blocking the shaft.
I need to change servo position step by step and check...
i re-uzip NCS1.5.0 ,using SEGGER Embedded studio or using bash.exe to creat a sample project ,and can not creat .the problem is
CMake Error at D:/v1.5.0/zephyr/cmake/zephyr_module...
Hi Nordic,
Aquick question with respect to the Thingy91. As part of our development, I am looking to the Thingy91 as a reference. In the Thingy91 design, it appears that...
Hi, I'm new to C language. I copied and pasted nordic example TWI codes to my self-defined SDP31.c file. And declared some of the functions in SDP31.h.
After clean and rebuild...
Hi
In other toolchain with GCC it is possibility to move some variable to a non initialiseed section
__attribute__((section(".non_init"))) int buffer[1000U];
When I...
