I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
I'm having a bit trouble here getting migrated to LPUART on a working nRF9160 <> HCI BLE on nRF52 (On the Thingy91). As far as I can tell my .conf and .overlay files are what...
Hello,
I've run into a problem, which seems at least to be similar to that described in another thread . In short, if I set up a counter with CC[n] and start it, a COMPARE...
Hi,
I would like to store important information (few MAC addresses) in flash memory at manufacturing stage. Then my program will be able to read these information thanks...
Hi ,
My environment:
nrf5340 DK board
nrf connect SDK v1.5.0
segger Studio IDE
I would like to establish communication from application core to network core...
Hello I want to make a python script that allows sniffing of 802.15.4 packets (nRF52840), The module exposes an API that allows starting and stopping the capture. I installed...
I am using windows 10, nrfConnect 5340, and the NRF5340DK.
I was searching for an example of how to configure and use the usart/uart 0 port as a 2 way interupt based serial...
Similar to this problem , I cannot open the serial let modem example for nrf9160dk_ns. I tried moving my nrf install to the root but did not help. I am using Windows 10. The...
I want to read the acceleration sensor value using the example of the ble-hid-keyboard, but if I let you read the acceleration sensor value, Bluetooth will be cut off. Can...
Hello, I am having trouble understanding the flashing process of an nrf52840. I have programmed a simple flashing example with the nRF5 SDK. I compiled the project using make...
Hi Nordic,
I am using the two nrf52840 units to test adv and scanning in a pair for the development. I am using BLE_GAP_PHY_CODED for both scan and advertisement. But...
Hi,
We have recently switched from using nrf52810 to nrf52840. Firmware porting went well until we tried using the BLE on nrf52840. No matter what we try the BLE will not...
Hi, dear Nordic
1) Could nRF52810 Serial Debug Pin be used as GPIO/I2C?
2) Some post mentions using the external circuit, so that the 2 Serial Wire Debug pins can be used...
Hello
We have developped a product with the nRF52832. Due to space restrictions we couldn't use the PCB antenna design from the nRF 52DK. We used an Johanson chip antenna...
nRF5340 datasheet page 2 states that the TX power is configurable from -20dBm to +3dBm. But later on in TX power section, it states the power level can go down to -40dBm....
Hi!
I am using SDK15.3.0, PCA10056 and Windows10.
I am notice, that if it will be hfclk request before usb launching and WFE in main loop, time for discover usb device...
