Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Dear Nordic Team,
I use a custom dev board with the nRF52832 SoC and the nRF5 SDK v16.0.0.
I need CoAP functionality for my project. I managed to get the CoAP Examples...
Hi guys, I am developing an mqtt-based app using board nrf9160. I tested the mqtt_simple example but it does not work. Here is my setup.
+ Broker server: test.mosquitto...
Hi, I'd like to set the alarm state of a minimal power configuration cluster that only has the attributes "remaining battery percentage" and "battery alarm id". However the...
Hi,
Is it possible to write to the UICR (with SES) without erasing it first?
Normally the boot loader sets the correct values in UICR, but for development I want to have...
Hello,
lately i've not been able to connect to NB-IoT network as i did before.
Long story short:
I'm working with nrf9160 since 3 months and i have been able to connect...
When the macro NRF_SDH_BLE_GATT_MAX_MTU_SIZE is changed in the sdk_config.h file of any example from the ble_peripheral folder, the slave sends the message Exchange MTU Request...
Hi,
I am using nrf mesh sdk 3.1.0. with nrf52832.
For iv update one condition is iv_timeout_limit_passed(m_net_state.iv_update.timeout_counter). The timeout_counter value...
Hi,
I am evaluating ble peripheral with nRF52840 SDK 16 and SoftDevice s140 on windows 10.
The SDK is copied at location: C:\Nordic_Semi\nRF5SDK160098a08e2\
The SoftDEvice...
Hello,
I am not able to connect the dots. After setting up the beacons, ( adopted ble_beacon_app from Sdk 16 ) how can I perform localization algorithm ( trilateration)...
Hello. I try to configure radio at NRF52811 to prepare antenna switching and get correct I/Q samples from different antennas. I have 2 antennas that are 6 cm apart from one...
hello, I try to make an application with 6 different services. I used the ble_custom_service tutorial to create my different services.
I manage to work without problems...
Hi,
I am working with the bsp.c functions. One of the actions is BSP_BUTTON_ACTION_PUSH, which the value is 1. I would like to know at which electrical signal it is related...
Hello All, I am having a trouble with the nReset Pin during Deep Sleep. The issue is that the board is waking up from Deep Sleep due to floating nReset Pin. I am using a nrf52480...
Hi,
I am currently working on a product based on an nRF52832 (SDK 15.3, S112 6.1).
The firmware uses the Nordic UART Service to receive and send data from and to a smartphone...
