Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
I came across a client example that use the
I read about BT_GATT_SUBSCRIBE_FLAG_VOLATILE
How I know if the subscription is not saved on the GATT server side (which...
Hi,
Is there any existing support for an e-ink display interfacing with the nRF52840? Something that already has an existing LVGL driver and can be integrated with an nRF...
Hi team,
I'm currently facing an issue with the nRF52832 and nRF52833 gateways in our setup. Here are the details:
Current Configuration: - Scan Interval: 100ms - Scan...
Hello everyone,
I have developed a program that utilizes UART communication, Bluetooth Mesh, and TWI/I²C functionalities, all within the framework of the Zephyr project...
HI,
I am building an IoT product using NRF58233 ICs. In which I use 3 PWM channels and 3 ADC channels. You can review the principle I attached to make sure nothing went...
Hi,
I have a strange problem. I use a serial port timer to retrieve serial port data. When I compile with debug, the program runs normally, but when I compile with release...
Hi,
I am using nRF52840 DK and Bluetooth Observer example program. I am implementing filtering. I am having trouble add include scan.h which is located at C:\ncs\v2.4.2...
Hi Support Team,
I have an nRF7002 DK board and I am using SDK v2.6.0. I am facing an issue when sending data from the client to the server. Below are the steps taken: 1...
Dear colleagues,
with the newer SDK (I am now using NCS v2.5.0 and 2.6.0), I have difficulties finding the right SYSTEM OFF mode current. Code currently looks like as follows...
Hi
I use nRF7002 with SDK v2.52, try to connect external MCU and use uart call back function, to recieved and send bcak the recieved data, It will happen fatal error and...
Hi,
I have bunch of SEDs (sensors/clients) and one or more FTDs (hosts) working on CoAP protocol. SEDs send data packets once in a while and mostly sleeping. I have few...
Hi,
I'm testing the NCS direction-finding-connectionless demo,
NCS V2.6.0
this is my overlay:
and my ant_patterns:
According to the white paper and some other...
Please, I want to flash Zigbee Weather station App on thingy53, I faced two problems:
1- i can't find the board in build configuration.
2- i tried to use programmer and...
Team Nordic,
Question for you. In nRF5340 datasheet, page 1, Flash and RAM description : https://infocenter.nordicsemi.com/pdf/nRF5340_PS_v1.3.pdf
I found description...
Hi,
I am developping a non blocking TWI (I2C) communication, calling this function:
The init function of the twi is :
Please note that the real code is splitted...
