I have so many versions of this topic that I now am certain that most of the answers provided are wrong. Since you cannot have so many ways of connecting an external nrf device...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hi, I have a problem in enabling both NAME filter and UUID filter in ble_uart_c SCANNER
I have enabled the both but
the device get connected only match with UUID but i...
HI
I am using the example of HTTP and HTTPS from this github link. I was unable to compile the example of HTTP and the HTTPS example is just hanged. no communication. I...
Hey all,
Custom service, but my first where I am looking for more than one byte of data written to a characteristic at a time - in this case 8 bytes. So everything looks...
Hi,
My project involves an nRF52840 DK connected to an accelerometer on a breadboard, connecting to my Mac via USB-micro.
I'm editing the twi_scanner SES project so that...
Recently I received the nRF5340-DK. I tested and it was working correctly and as a test, I compile one of the ready solutions of NRF5340 of SEGGER Embedded Studio. Everything...
Hi, I am getting an error 19 which causes a reset after some time running a modified version of the ble_nus peripheral example may someone guide me on how to sort the issue...
Hi, what is the nRF52DK UART, for the nRF52832, flow control when using the ble_app_uart_pca10040_s132 example? It appears to be possible interrupt driven based on data received...
So ...
I'm still trying to get peripheral_uart running.
I'm using a nRF53 PDK (PCA 10095 - rev 0.8.0) (I've received two 0.11.0 boards, both of which died).
I'm using...
I'm using the nrfx twim driver along with Zephyr. I'm using the NRFX_TWIM_EVT_DONE to initiate a subsequent TWIM command and finding that the second command fails due to the...
Dear community,
I was working with a modified code based on an example for switching the leds on/off in a Mesh BLE network. Everything was working well until I tried to...
hello Nordic
i am using nrf52840, SDK16.0, a project build on the peripheral app_ble_blinky example
i am trying to use QSPI but the write function falls on error no...
Hello together,
I try to get the asset_tracker_v2 up and running on the thingy:91.
At the moment I get an Error from AWS_iot aws_iot: mqtt_connect, error: -116
My problem...
Hi Nordic,
I am trying to use the nrf52840 to talk with my 4G module on baud rate of 115200 , but I find it always come into error for the recving the uart data. Also it...
Hello,
I have an nRF9160 development kit and was measuring the time it takes for switching off the modem
when it has an open data connection.
I did it by sending an...
Hi,
I'm currently working on NRF52832 (Softdevice s132 6.1.0) controller and developed a firmware from light switch client to develop a mesh network and its working fine...
