Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
I suspect a possible race condition happening during NUS service discoveries. I have two peripherals that are advertising and have DIS, Battery and the NUS service enabled...
Hello,
I have configured max30101 with nrf51 and I want to read the fifo of max30101. The fifo can contain 32 samples and the size of each sample could vary from 3-9 bytes...
I followed the suggestions in https://devzone.nordicsemi.com/f/nordic-q-a/51642/can-t-build-nrf-connect-asset-tracker
But, still having the same issue.
Using tag v1.0...
On one of our products, we are experiencing approximately 4% failures during production. I traced the problem to be caused by function sd_softdevice_enable not returning....
Hi Devs,
based on this example
https://github.com/NordicPlayground/nRF52-Bluetooth-Course
i was able to run it, and the value field appear below the Unknown Characteristics...
Hello Everyone, I newbie to BLE world and new to programming. Currently I am following this github repo: https://github.com/sandeepmistry/arduino-BLEPeripheral . I am using...
Dear team, Device - nRF52832 SDK - nRF_SDK_15.0.0 Softdevice - s132_nrf_6.0.0 IDE - Segger embedded studio
My application needs to toggle one gpio pin using app timer in...
I'm developing for the nrf9160 and would like to clone the sample projects at https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160
branch nrf9160_samples...
Hello,
I'm using SDK15.3 (Generic_Stack_S332_06.01.01).
IROM1 Add :0x30000
IRAM1 Add : 0x20003600
Central Firmware support already in SDK14.3 just I move this part...
I have made a state machine in which
I first initialize gpios, power management, clocks, and ble stack
I then put nrf into deep sleep (System OFF) state
A wakeup signal...
Does the http FOTA_download client support 301 responses, ie permanent redirects? I want to move the download file from a hired space to our server. Is using permanent redirects...
Previously I have been successful getting the AWS FOTA update working using the AWS FOTA example project, the example update.bin file and location provided
by Nordic for...
Hello there,
I am working in my master degree project with nordic NRF51822 microcontroller, but I faced two problems. I don't know if is a SD problem or hardware problem...
I've been tested for BT SIG however have met error which sent 0xc000 and got 0xc000. I expected to receive 0x8xxx. Command is LE_TEST_END in DTM.
I tested with nRF52832...
Hi!
I have old code written in nRF51 enviorment with SDK nRF5_SDK_12.0.0.
I've successfully flashed the softDevice (s130_nrf51_2.0.1_softdevice.hex).
No error occurs...
