Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Environment:
I can't seem to get the one button sample to do anything... I get a steady ~1sec flash from HOST led on the npm1300, but I get nothing from pushing SHPHLD...
Hi Team,
I have 1 nRF5340 Audio DK. With the steps mentioned in below links, I configured Json file to Headset and I'm able to achieve it.
Setup Details : Headset - nRF5340...
With nRF as advertising peripheral, is it possible to measure RSSI of active scanners' SCAN_REQ packets. `bt_le_ext_adv_cb` has a `scanned` callback, but it looks like it...
Currently, the nRF5340 Audio is set up and running as follows: In CIS mode, the audio source is I2S
Gateway side: nRF5340 Audio DK I2S settings are default Headset side...
Currently, my client IDO is using the NRF54L for development. They are designing their own PCBA.
They need to evaluate two question:
Question 1:
They need 4 ADCs, 4...
I' m using custom board of nrf5340 with nrf7002, and the SDK version is ncs v2.5.2.
I've tried to build and run, but the log in RTT viewer is only print the line "Bringing...
Hi,
I am using the nPM1300 in combination with a STM32L431KBU MCU.
Also the code from Nordic to communicate with the nPM1300: https://github.com/NordicSemiconductor/npmx...
https://github.com/zephyrproject-rtos/zephyr/blob/main/samples/drivers/spi_flash/src/main.c#L36 may I know where I can find the pin connections used in this example
"const...
OS: Window11
Programmer version : v4.4.0
Used Chip: nRF5340
Used Hex file: peripheral_uart_nrf5340dk.hex
An error occurred while Erase&Write the Hex file while testing...
Hello,
I am trying to make radio test functions work on my 52840-based board using SDK 2.5.2. After some effort I managed to create a simple test program that partially...
Hi,
I’m trying to have two nrf9161s exchange data back and forth as quickly as possible. Initially the first radio is transmitting, and the other is receiving (3 sub-slots...
The default setting for the external flash chip of 9160dk appears to be 64m, but when used, the log display only shows 8m, and only the part within 8m can be used,
Then...
Hello,
I am trying to use PWM to control two LEDS, one red and one green (referred to as blueled in the code) to produce different colours. I have had a look at the example...
Hello,
When we flash the BLE Zephyr project to the external chip (nRF52833), do we need to add the SoftDevice controller .hex file as well, or does the merged .hex file...
Hi All,
I have recently design my version 2 of my custom board, everything seems to work on the board, the firmware is fully running but i can't see the BLE device on...