Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1 I have two quick questions. 1) How to add version information(string) when make binary. 2) How can I read version when I finish...
Could you pls advise what control is there over the output voltage on PPK2?
For example, the STM power monitor only supports discrete output voltages such as 1.8V, 2.4V...
Dear Support Team,
I'm trying to test 802.15.4 feature with the precompiled radio_test hex file, but got an error when connecting the CLI through PuTTY. Below is the detail...
I am very new to the Nordic line and I have an nRF5340-DK that I would like to build a basic BLE Remote Control project. The Remote Control must pair with a phone or computer...
Hi,
I am using VS code for my project, which is using bl653 board. While in build configuration setup in vs code am getting this error. ERROR: source directory - does not...
Trying to add UART capability (sample project from console) to a a ESB transmit sample project. Could not get a build assert to work.
1) Tried to add all of the selections...
Hello,
On a BLE Central, how can I enable connect with auto connect to a peripheral with previously saved bonding information.
Once paired and bonded, I can recall bonding...
Hi everyone,
I am updating firmware for mesh using following this commands:
PS D:\nrf5_SDK_for_Mesh_v5.0.0_src> nrfjprog --program .\bin\softdevice\s140_nrf52_7.2.0_softdevice...
Hi everyone. I am writing to have an important info, that is, is it possible to load a .hex file, preloaded in an external flash, to program from my application in the nRF52840...
Hi,
As shown in the subject, I am developing a product which needs to support extern Flash-based BT OTA-upgrade. So w here can I find examples of OTA-upgrade using external...
Hi Nordic
In our product, nRF52832 is connected with another MCU through UART. We find that the overshoot in UART signal is very high.
The yellow one is the TX signal...
Dear All
I am trying connect/disconnect function with the DK, it gives me some reason codes, my app is based on central_multilink, which I cannot find their meanings, could...
Hi nordic in our product nrf52832,guided by the tutorial developer.nordicsemi.com/.../README.html,we find something strange. as we have 3 nrf52832 chips in our product,two...
Greetings,
One query on the very useful eDRx notifications in NB-IoT mode (nRF9160 SDK running 1.3.1 FW, used with MoSh app) :
I have just noticed that sometimes when...
With reference to the following known issue: NCSIDB-114: Default logging causes for nrf connect sdk 1.3.2. Is there any further documentation regarding the workaround mentioned...
