Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Hello, I use nrf9160dk, ncs v1.6.1.
I'm trying to use both AWS IoT to store some data from the DK board, and to connect to nrfcloud for AGPS data. I don't have any previous...
Hi All,
I am beginner in development on Nordic product.
I am using sdk v1.5.1 and nrf5340 for development.
I want to add open source library libcorrect.a for Forward...
Hi.
i use
i call i2c_write() and if the buffer is large(8kB) i get error in i2c transfer -5.
i go deeply and found that it is due too error -11:
If i step into...
hi, I am new to Nordic development, and I have to write a VC# Windows App to connect with a BLE GATT oximeter (based on an nRF SOC) through nRF52840 dongle in a few days....
Hello,
I am designing a set of equipment, one to transmit voice and the other 200 to receive voice (One person speaks and 200 people listen). It is 8kByte/s low-quality...
Hello !
I have found that AES operations are fastest if cc310 is used directly : examples/crypto/nrf_cc310/aes
Do you have any integration guide for library what use on...
I have to implement async communication between two nRF52832 chips. I am using two nRF52dk boards and nRF Connect SDK v1.8.0.
Following this case:
https://devzone.nordicsemi...
Hi Community,
Recently I have started testing my BLE peripheral running HRS with iPhone. My device is running SDK16 on nRF52 SoC. This is working perfectly with Android...
Can I use this aerial: https://thepihut.com/products/pycom-lte-m-cellular-antenna with the Thingy91 LTE-M interface. I am unsure whether the Thingy91 has a uFL connector as...
We are developing part of an application for products that are supposed to have 10+ years of service life with updates over the whole lifetime. We want to have a flash memory...
The PS for the nRF52840 indicates that the current consumption when the radio is transmitting BLE at 1Mbps is 16.4mA (p61). There is no mention of current consumption at 2...
Hello, I'd like to check what is the typical distance using 0 dBm tx power using Nrf52840?
I am using this BLE module based on Nordic, and it seems to work ONLY 2-3m far...
Hello
I am getting started with Nordic devices.
I recently bought a Thingy:91 and followed a tutorial to load the Asset Tracker application on to the device – this...
Dear,
We have been using QSPI external flash (MX25R64 installed at nrf5340 DK board) to write data. Particularly, when we ran flash_area_erase function ( located at zephyr...
