Developing on the nrf51822
Have working code for the nRF52840 Dongle using the pc-ble-driver therefore all Bluetooth work is done using sd_* calls. The PC provides easy...
Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hello,
I'm new to sniffing BLE. I'd like to determine the min and max connection interval and other connection parameters (MTU, slave latency, supervisory timeout, etc....
I am just starting development of a BLE mesh product on the nRF52840 using the serial demo on the nRF52840DK. By default PERSISTENT_STORAGE=0 in the demo so the nodes forget...
Hi,
I have a Unix time stamp value stored on the Nordic board that comes from a GATT connection.
I am using SDK 15 s140 pca10056 NRF52840-dk.
I need to update this value...
I am using nrf52840 dk for zigbee project with two xbee modules. One xbee is configured as coordinator and other as end device and nrf board is supposed to act as router....
I use nRF52810 + 15.3.0 s112 to develop. After the equipment upgrade is successful, I power up the equipment again, and the equipment is always in DFU mode.
For some reason it seems that the TWI master does not generate a NACK. As a consequence, the TWI slave keeps sending data. I have managed to create a very simple function...
Hi
I have a really strange issue with an NRF52840. I'm using it with an MPU-9250 connected via TWI. I've modifed the excellent library:
https://github.com/Martinsbl/nrf5...
I want to use RTC handler , so I used NRF_DRV_RTC_INSTANCE.
I use SDK 16.0.
" 'NRFX_RTC"_INST_IDX' undeclared here (not in a function) ; did you mean 'NRFX_RTC_INT_TICK...
I've been reading into the "nRF5 SDK for Thread and Zigbee v4.0.0", and I wondered about the limitations , in specific
is that a hardcoded limitation, or does it require...
Hi I programmed the nRF mesh experimental dimming example on the nRF52832 chip. I noticed that, when using Bluetooth Mesh provisioning apps (I've tried several to verify this...
I am trying to setup a PPI channel to trigger the SAADC in simple mode. However, it appears as though the SAADC module is disabled after every read. I.e. if I write:
...
I am unable to flash the DK board facing issue " Failed to Connect to Target. No idcode detected. Please check connections and Target interface Type."
DK Board Details:...
I am using LSM9DS1 IMU, nRF52840 with SDK v16.0.0. I configured the IMU to raise an interrupt when the FIFO buffer be full by writing to register INT2_CTRL the value '0b00011000...
I can't see it!
https://www.nordicsemi.com/Software-and-Tools/Development-Tools/nRF-Connect-for-desktop
The 'Downloads' section contains only the "host" native app - doesn...
I am trying to interface the BMM150 magnetometer with the nRF58240 MICRCONTROLLER, Iam able to establish the I2C connection and get the return value from the reg 0x40 and...
