I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hello!
Does anyone know of a library for the I2C LCD 16x2 display? I found the library by lovee, https://devzone.nordicsemi.com/f/nordic-q-a/23401/nrf52832-connect-with...
Hi,
I want to use AES CCM in my project (I want to try both CC310 and mbedTLS).
When I compile my project, I have undefined reference to 3 functions that are located...
We have a 52832 device that is showing some possible flash corruption during programming. Does the softdevice perform an integrity check on startup such that a corrupted softdevice...
Hi I am using nRF52832 .My application acts as central and Peripheral at the same time.
board acting as Central: scans and connect to peripherals without any error.
But...
Hi,
I'm using nrf52840 and a barcode reader by UART using softwareSerial.h library, it works fine. I am also using the bluefruit.h library to communicate by bluetooth that...
I'm modifying the DFU example app in SDK 15.3, for the nRF52840.
attempting to call fds_record_update or fds_record_write within the context of app/main.c ble_evt_handler...
nRF5_SDK_11.0.0_new\examples\ble_peripheral\experimental_ble_app_eddystone\pca10028\s130\arm5_no_packs
Using the above mentioned example on a custom board with nf51822....
Hi,
I am working on a custom board with the 52840 chip. The problem I'm facing is that when I plug in my custom board, Windows 10 immediately shows a USB malfunction error...
Before my 52840 acting as central is connecting, it scans with the following params list:
static ble_gap_scan_params_t const m_scan_params = { #ifdef BOARD_PCA10056 .extended...
Hi i am using nrf52840 DK and i am trying out sleep_mode after timeout happens. but i had a doubt in ble_adv_evt_idle i.e if i use this case the device goes into sleep and...
Dear all,
I have a problem.The DFU could not be performed due to a large size of the application around 300kB.
Platform : 52832;
SDK: SDK_11.0.0;
softdevice:s132.
If we edit the example code in seggar embedded, are the same changes done for the hex files of the same examples? IF not how do we change the code and put it in the dongle...
Hi,
I was following the instructions laid out in the "Configuring DFU over Mesh" guide in the nRF5 SDK for Mesh v3.1.0 ( https://infocenter.nordicsemi.com/topic/com.nordic...
Hello All,
I am working on nRF51822 custom board and i am not change it because it is customer requirement. Use IAR embedded workbanch IDE in windows 7. For reference...
This post mentions that only logical address 0 is supported for the coded PHY.
Is there any additional explanation for why this is? The OPS does not mention this.
...
