Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Hi!
I have a problem with UART. SDK15. S132 6.0, nRF52832
I added UART to my project and watching strange behavior: when I attempt to send anything to UART
project...
Dear Nordic Tech Support and Developers,
Hello. I have implemented the Mesh Demo (light switch example) with Nordic Thingy 52. I would like to inquire an info on the side...
I'm using SDK12 and SES.
I compiled my code based on ble_app_uart example for nRF51822_QFAA and I see in Memory usage that RAM is at correct addresses (finishes at 0x20003FFF...
hi...
i am working on mesh , i have done light switch example , now i want to get some message from node and send to particular node . how to print the same message which...
Since the Mini 2MP is obsolete
Via this link https://www.amazon.com/Arducam-Module-Megapixels-Arduino-Mega2560/dp/B012UXNDOY only can buy Mini-2MP-Plus
The official git...
Hi,
I am using 2 gpio interrupts from 2 separate sensors with active soft device. one sensor generates interrupts at around 400-800 ms and the other comparatively lesser...
Hi,
So I am trying to poll the signal strength of the nRF9160 DK and at first everything seems okay, the device gains connection and all the boxes in the LTE Link Monitor...
We have added Nordic Uart Service (NUS) into the nRF mesh code and we created two mobile application.
First mobile application:
- is for nRF mesh provisioning which is...
Hi,
The datasheet for the antenna used in the dev kit, P822601, has its specification performance measured on a PCB DUT at 140 x 50 mm^2 - which seems rather unnecessary...
HI !
i have a problem during importing nrf9160 project in SES , knowing that i imported this project and others with same toolchain installed and other requirement.
onetime...
hi all
i have been working on a raspberry pi hat design and i would like feedback on it's design
this is the link to the github repo and i do update it regularly https...
hi,everyone
I want to run the DFU example in meshV3.1.0 . but i still can't understader how to run it . below is my understanding:
1.ther are must have 2 devices , A device...
Hey, i having problems with uploading code to my Thingy52.
Equipment that i using: nRF DK https://www.nordicsemi.com/Software-and-Tools/Development-Kits/nRF52-DK Nordic...
Having issue with nrf52840 interface with sim808 for GPRS connection. I am trying to interface nrf52840 with sim808 using UART. But only AT and ATD command reply i can see...
Hi,
I am currently trying to test the capability of bluetooth 5 long range mode using a pair of SparkFun Pro nRF52840. I have used the blue-app-uart example and:
1)...
