Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
I'm using the "ble_app_uart" example from "nRF5_SDK_15.2.0_9412b96". I would like to enable the sending of logs to the serial port (Virtual com), like "printf ()".
The code...
I'm trying to do a low power sleep of 1s directly after a device reset, i.e. in Reset_Handler().
During this stage, my application does not allow any interrupts.
So my...
Hello DevZone community!
I'm having trouble debugging more than one board at the same time in a Linux development environment.
For a single board, I can debug either...
hello, i am using nrf52 dk .I was testing example twi scanner.I want to read slave address.So i am using twi scanner example but i got error message as follow:
TWI:INFO...
Hi, I'm new here and I use nRF52832 (pca10040), I was wondering if it is possible to change a function in C / C ++ language during the runtime, that is, my idea is whenever...
Hi,
I had a problem using your (nRf's) implementation of block device with my flash memory (I think that exact model is not relevant here). I'm using SDK 15.2 with NRF52840...
Hi,
Do you have a declaration of conformity for the chipset nRF52832 ?
I need this document to justify to my laboratory the conformity of the Bluetooth module to the standard...
hi,
I have some questions, please help me solve these questions. ( I use SDK 15.2.0 and nRF52832)
1. my customer ask how many central bonded with one nrf52? (my project...
Hello,
I am trying to send data from my light switch mesh client (nRF52840) to my gateway, the nRF9160 using UART. I added the UART functionality to the light switch client...
Hello there,
I followed all the steps in the following link:
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.nrf52%2Fdita%2Fnrf52%2Fdevelopment...
My device (nrf52832) has two signals triggering GPIOTE interrupts. I need to be as low power as possible, so both are setup to not use hi accuracy, making them share the PORT...
i need a help
As mentioned in this thread
https://devzone.nordicsemi.com/f/nordic-q-a/18512/directed-advertising-with-pre-shared-irk
in need to do directed advertising...
Hi,
We want to measure our external custom board which is not based on nRF52 chip. That board has current consumption header and it's chip draws maximum current of 60mA...
Hi:
I find a odd question when i use SES to develop nRF52832, ESB protocol is using and i need to config some different slaves with same code except the pipe num, i define...
Hello,
In my current zigbee project I have a sensor end device which should sleep when possible. I am handling the ZB_COMMON_SIGNAL_CAN_SLEEP event and have added zb_set_rx_on_when_idle...
