Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Hi,
I'm collecting data from BLE and storing them into nRF52840 Dongle by using nrf_fstorage_write procedure. Everything works fine so I can write data into flash by nrf_fstorage_write...
When I run the TWI scanner example, an unknown address shows up in tandem with my TWI device address.
I am connecting a MAX30101 EV kit daughter board to the nRF52840...
In the secure DFU bootloader, I have some custom initialization that I need to happen after the BLE transport is initialized in nrf_dfu_init(), but before loop_forever() in...
Hello everyone,
I've got an issue with ESB. I'm using 3 nRFs 52840 with firmware based on SDK 15.2. One of them, the radio-receiver is RX, and two of them, PilotA and...
Hi,
I'm working on putting our system into low power idle mode. We use MyNewt to build our application. In order to get to the lowest power, I disabled BLE and all our drivers...
SDK 15.2, S132 6.1, nRF52832
I have a characteristics to write data to a peripheral, using variable length up to 507 bytes and authorization.
Writing to the peripheral...
I'm trying to get the code below to compile. One question is how to fill in the nrf_crypto_hash_info_t structure. Another issue is that the nrf crypto includes don't compile...
Chip: nrf52840
Platform: Android
MacOS Dev
There is pretty much no error logs but it can't actually send anything over mesh network on udp. Seems to receive without...
I have a RedBear BLE Nano v2 (nrf52832) connected to 3 AA batteries for power. I also have a Maxbotix (MB1043) ultrasonic sensor attached. I have configured a gpio pin for...
Hi, I am a beginner to nrf24le1. My company has products made of nef24le1. I would like to debug nrf24le1 devices but couldnt able to , I would like to know the answers for...
Hi. I am trying to run the makefile of ble_app_blinky (from SDK 15.2.0) on Ubuntu 18.04 and Visual Studio Code. When running "make" in the armgcc directory, the following...
i have recently upgraded to SDK 15.2, and since doing so I am struggling to get timestamps working in the logger.
I am initialising the logger here:
And here is my microsecond...
Hi all,
I've just downloaded SDK 15.2.0 on Windows 10 and it was unable to unzip the file and reported an error. I copied the file to Mac OS and got the same error.
Is...
Hi ,all.
I now need a open bootload through BLE.But I found it hard to modify it from the secure ble bootload example。
Any open bootload examples of 52832 through BLE...
Hi,
I try the last days very often to Recover my NRF52 Chips on NRFGO Studio 1.21.2.10.
Error: Unable to find or open the JLinkARM dll, Unknown Error.
I reinstall...
