Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Hello, i have this problem with DFU, in Mesh SDK v3.0, i am using PCA10040.
this is my boodloader_config_default.json
and i am using this for make the pkg.
and...
Hi!
For our development purposes I am implementing NRFUTIL 0.3 for mesh on Android/Java, migrating it from Python code, via UART/Serial, for DFU purposes
It looks like...
Hello,
I am having difficulty using a single TWI to support a DAC (MCP4725) and IMU (BNO055).
I am using nRF52 DK, and SDK 14.3 with the SEGGER IDE. The DAC is running...
Hi,
I am trying to run lte_ble_gateway sample on nrf9160 DK, but in debug I can not catch breakpoint on main().
When I going in debug mode step by step I find that the...
Hi
I am new to the NRF52840. I am trying to receive data from nrf24L01+ to the nrf52840 Development kit. I find some examples from the SDK radio receiver using PCAl0056...
Hello all：
I am using nRF52-DK（pca10040）to do some tests.
I want to use gazell and at the same time, I want to detect the events of the NRF_RADIO, connect it to PPI. ...
Hello,
I am using Eclipse to create a project using code from ble_app_hrs and I am developing for a nrf52832 chip. Unfortunately, I am getting a "was not declared in this...
I send a sequence of characteristic writes to my device, in code based on the nRF Toolbox. Sometimes I see this error message. Why does it happen and what steps can I take...
Hi Team
I created an own interface layer using the mesh SDK's "flash_manager" to have a simple API for accessing my application flash area.
Now, I am facing the problem...
Hi there,
I am migrating a project from SDK13 to SDK15.2, where I need to change the advertising data dynamically and change the ble_gap_adv_params_t properties type between...
I am using SDK12 with nrf52832. UART working fine (with FIFO) and Timer1 also works.
I wanted to set a 1 minute timeout around the UART dialog to handle disconnection etc...
Hi, watched your long distance test video. I can find the code in the file NRF5_SDK_15.2.0_9412b96.
How to change the output power (db type example 2 db or 3db)
Hello, I am currently evaluating the nrf52840 and nrf52832 for the purpose of bluetooth mesh. I found flash usage information in the mesh SDK documentation as follows:
Build...
So I'm very new to the Nordic nRF52 and nRF5 SDK. I'm using the blinky examples as a starting point for a remote control that will drive motors. My customer's question is...
As per my requirement, I need strong pairing mechanism, i am referring ble_app_gls example of nRF5_SDK_15.2.0_9412b96 sdk for checking pairing. As i have seen in the code...
