Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
sometimes it discovery service no matter ,sometimes it stuck when call sd_ble_gattc_primary_services_discover and no callback event 。 why it is ? is a bug ?
HI,
Under nRF5_SDK_12.2.0_f012efa, with s132_nrf52_3.0.0_softdevice, run on system on low power mode.
I define an app_timer,below is my parameter
APP_TIMER_DEF(m_second_id...
Dear Nordic community
(SDK v14.2, nRF52832)
I have a real-time application where I am sending 6 packet of 20 byte Notification per connection interval. And there is not...
Hi,
When debugging with sdk_15.0.0 ble_app_butonless_dfu project(application project) + secure bootloader project(bootloader project),it will cost about 2~3 minutes for...
Hi,
I am trying to modify the multilink central example to send string to other board.
In the main.c I inserted the uart_init(), uart_event_handle() methods
I added...
Hi everybody,
I'm developing an product with :
NRF52840, V0.9.0, SDK15
In the DK I connected LIS3DH (accelerometer by TWI)
all works.I configuration of HZ and temperature...
Dear Nordic team,
I want to add DFU services to an existing application which is based on ble_app_uart example.( SDK 15.0.0, softdevice S132 6.0.0)
What I have done is...
Im working on merging blinky_c with light_switch_server. Took the blinky example as starting point then merge the mesh code accorging the Coexistence with nRF5 SDK BLE functionality...
The issue is that I fixed some of your bugs in the attached file, as follows:
Changed to handle larger number of records greater than 256 records, we need 500 records...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
hello
Im trying to send a small array with two integers over bluetooth mesh
but Im getting error code 7 invalid params..
how should I send an array like this?...
Hi,
I am working on PB Remote example. I would like to be able to run remote scan on my 5 servers immediately after they are provisioned.
For example, I provision the...
I have been using nRF Connect on a Samsung phone for a couple of months, and have forgotten how to install it. My daughter was playing with the phone and managed a factory...
I'm working on a BLE design for nRF52832, with SoftDevice S132 v5.0.0. The project uses FreeRTOS with Tickless Idle enabled. When the user powers the device off (from a UI...
Good morning,
I've inherited a line of nRF51822-powered products that are currently running firmware based on SDK10 and SD130 v1.0.0. UICR-> BOOTLOADERADDR is set to 0x3b000...