Hi
I try to run BLE HRS collector example.
when I run the project, in RTT terminal I have these error
00> sd_ble_enable: app_ram_base should be adjusted to 0x20001CD8...
Google open-sources the firmware needed to build hardware security keys
Google open-sourced today OpenSK, a Rust-based project to aid hardware vendors build hardware security...
I would like to store a simple integer value in the flash write and read after some event. I'm using the mesh example Dimming examples (experimental) in the nRF5 SDK for Mesh...
Hello,
Has there been any success with getting the python bindings for the pc-ble-driver running on openwrt? I've succeeded with the driver itself but not the bindings....
Hi Nordic Team,
In my BLE project I'm creating a Test application which gets all the advertising data from peripheral devices. The complete list of scanned device is received...
Hello all,
According to the documentation and this feedback on a case there is a maximum size for a particular cert before nrf_inbuilt_key_write returns NRF_ENOBUFS . Can...
Hello,
I am using nrf52840 DK, Segger Studio IDE, Win10.
My application is I want to transfer the image from iOS to the DK board.
I am aware of the Image Transfer...
Hi Nordic team
I failed to demostarte multicell location sample.
Hardware: Thingy91
SDK: v1.6.0/multicell location
Modem: v1.3.0
Q1. At prj.conf, nrf cloud location...
Hi Nordic
We are developing our IOT product and we are starting our development of firmware on nRF9160 DK so that we can port that code to our custom PCB that will contain...
Hi,
My application is currently using s132 v5.1.0. The Release notes for s132 v6.0.0 say:
"Fixed an issue where incorrect timing calculations during the LE Data Length...
Hello
I am running this version of SES
SEGGER Embedded Studio for ARM
Release 5.34a Build 2021011401.44914
Nordic Edition
Windows x64
When I run my program in...
Hello,
I am using the pine watch hardware, to do some tests,
I configured through the overlay file, the I2C_1 to use pins 0.6, 0.7 as shown below,
&i2c1 { compatible...
Hello,
I'm playing with the timing subsystem in order to measure some execution time with higher granularity than the RTC tick on nRF52840 (using PCA10056 DK).
I'm specifically...
Hello sir,
I am using nrf58232 Dev kit board in which when my BLE goes is in advertisement board and after couple of seconds advertise APP_ADV_DURATION is expired then it...
Similar, unresolved issue can be seen here .
I just got my official nRF52840DK and setup nRF Connect on my MacBook. I'm able to build the Blinky example and flash it...
Hi,
I have the following in my code to measure throughput over the Nordic Uart Service.
It works, but I was wondering if I am measuring correctly. I took this measurement...
Hello all,
I'm working on a BLE central application based on nRF Connect SDK V1.6.1. The application connects to certain BLE peripheral devices and does a service discovery...
Hello,
I have been building an application using the CLI and I am thankful for the CLI example and how well it works. I am wondering is it possible to use the CLI but...
Hello, Im using SMP over UDP (OpenThread) and after updating to v1.6.0 in NCS, sending most commands with `mcumgr-cli` makes the device restart with:
This happens for most...
We are currently experiencing malfunction with the big chip on nRF9160dk board, which provides USB-UART and jLink functionality. After 30 minutes, to a few hours, we either...
I have nrf52832 dk. I used power down example by github
https://github.com/NordicPlayground/nrf51-powerdown-examples : system off wakeup on gpio. Upon current measuement...
