Hi
I try to run BLE HRS collector example.
when I run the project, in RTT terminal I have these error
00> sd_ble_enable: app_ram_base should be adjusted to 0x20001CD8...
Google open-sources the firmware needed to build hardware security keys
Google open-sourced today OpenSK, a Rust-based project to aid hardware vendors build hardware security...
I would like to store a simple integer value in the flash write and read after some event. I'm using the mesh example Dimming examples (experimental) in the nRF5 SDK for Mesh...
Hello,
Has there been any success with getting the python bindings for the pc-ble-driver running on openwrt? I've succeeded with the driver itself but not the bindings....
Hi Nordic Team,
In my BLE project I'm creating a Test application which gets all the advertising data from peripheral devices. The complete list of scanned device is received...
Hello all,
According to the documentation and this feedback on a case there is a maximum size for a particular cert before nrf_inbuilt_key_write returns NRF_ENOBUFS . Can...
Hello,
I am using nrf52840 DK, Segger Studio IDE, Win10.
My application is I want to transfer the image from iOS to the DK board.
I am aware of the Image Transfer...
Is there a way to read the nRF9160 modem firmware revision? I am certain we will need to know it at some point if for no other reason than to help debug an issue, such as...
Hi all,
from the following webpage, I found the there are3 module will support long range , 52811 ,52833 52840, I wanted to confirm that the long range support in 52811...
Tried connecting a J-Link Lite to the debug port of the Thingy:91, get an error message
ERROR: Low voltage detected at the target. Please make sure the device is
ERROR...
Hi,
After a recent windows update I found that when Segger Embedded Studio starts it gives a pop-up No commercial-use license detected. Solution compiles ok. Can this cause...
Hi, I try to update a nRF52832 with SDK 14.2.0 to SDK 15.3. I created a package with SD + BL + APP with the following command:
I'm using nrfutil (v5.1.0) to download the...
Hi,
We are trying to power optimise our device but in the sleep/powerdown mode we seem to be using much more power than expected.
I am seeing consumption of approx 330uA...
I have a question regarding Direction Finding on nRF52833. I cant see any examples related to this in new SDK 16, also I cant see any antenna array recommendation. Do you...
When building a project I get a number of undefined symbols:
.\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol __start_fs_data (referred from nrf_fstorage.o)....
Hi,
I am planning to design a custom board using nrf52840 Soc which receive analog signal from sensor and send ADC outputs through UART to smartphones using Bluetooth communication...
Hi, Everyone
I use sdk15.2 & nrf52832
I am doing a test to read the slave address in TWI
There is one slave device on the board and the slave address is 0x68
I used three...
I am working with SPIS example ( sdk version 15.3). SPI master send data regulaly. For example, it sent 5ms cs low, but there are only two bytes transferred, the first byte...
Hi,
I'm working on a project that is using the the freeRTOS and I want to use the NFC pins P0.9 P0.10 to drive SOFTWARE SERIAL UART with a timer like TIMER1, when I try...
iPhone 8 Plus with nRF connect App[iOS], does not shows BLE 5 beacon in scanning, it only scanning BLE 4 beacons, In Spec of phone it shows it support BLE 5
nRF connect...
Hello,
I follow the nRF Connect SDK on a Windows 10 x64 computer and it's a crap. I get a lot of errors like this one. It's so crappy that I doubt that I will continue with...
