Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Dear Sr.,
Can't detect carrier
They are two PCB one TX Carrier and other mush Detect the carrier ---------------------------------------------------------------------...
mains.c
Hello Everyone,
I have deveLoped the Custom PCB whixh has the push button which is connected to VCC so i would like verify my software logic for button configuration...
Hi,
We have a new product based on the NRF52840. We are trying to add NFC record text to the firmware that based on SDK15. We could get the NFC record text from the NRF52840...
We're evaluating the nrf52840 and I am looking at the SPIM peripheral. The datasheet states the following:
"If several AHB bus masters try to access the same AHB slave at...
i am working on the Cycling Speed and Cadence sensor central configuration using nRF52832 DK in Segger Embedded Studio. I used the RSCS central example of nrf_sdk_v15.0 and...
I'm trying to migrate a working application from SDK 14.0.0 to SDK 14.2.0. I was using app_twi on SDK 14.0.0 and am now using nrf_twi_mngr on SDK 14.2.0. One difference is...
Hi all,
Just noticed the RTT logs are broken with GCC in SDK14.2 while they work fine in SDK14.1
I found the cause is the definition of the macros:
/*
* For GCC...
Hello.
I am working with a custom board. I have been wondering how to change the default polarity for a pin? I need LED_1 to have a polarity and the other 3 LEDs to have...
Hello,
I base on migration guide:
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.1.0%2Fnrfx_migration_user_guide.html&cp=4_0_0_2_5...
Hello,
I found the link below and was wondering if the information is up to date (says nRF52 SDK v0.9.2 ).
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic...
Hello,
I am using nRF52480, s140 , SDK_15.0 and using a central example. I can print the scanned RSSI, and MAC address of the each advertising packets with BLE_GAP_EVT_ADV_REPORT...
Hi, I'm trying to increase the NRF_SDH_BLE_PERIPHERAL_LINK_COUNT to max possible (20) in my project. When I first tried to do this the softdevice prompted me with this error...
Looking to better understand bsp_indication_set.
As per the example custom_ble_service_example found on github, ...when DK is connected, LED_1 is lit and stays lit from...
Hi,
I'm developing an application for nrf52840 that's essentially based on both the USB MSC example and the BLE NUS example in SDK 14. I started with the USB MSC example...
Hi,
I am using sdk 14.2.0 ble_app_hrs_freertos example.
two threads i have created, threads are having nested loop inside.
for this case, thread is stucking inside loop...
