I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hi, I am working on a project that utilizes the nRF52832. How to properly enable Access Port protection in the code, if I want to have a single firmware for all three revisions...
Hi,
I was using the Direct Test mode app from the nRF desktop to try to run a DTM Tx Test on nRF54L15-DK. The app could find the device (but there're two serial ports xxx51...
Hello,
I am currently working on a project using the nRF54 Series and I am evaluating the capabilities of the CRACEN versus the nrf_oberon software library.
I would like...
Hi,
I am wondering why can't CODED PHY and BLE Audio be modded into the nRF52832. Are there any hardware requirements for both to be supported ? If so, is there any info...
I observed that I can't flash my board in VS Code when a USB-serial adapter is connected to my computer. When the adapter is unplugged everything works.
The interesing...
nRF54L15 + NCS 3.02 + Toolchain 3.02
So I have followed Dev Acadamy exercises for Serial Recovery and BLE FOTA. In my project I now have MCUBOOT for Serial Recovery but...
Hi, we are writing the register TASKENTERSHIPMODE to enter ship mode, and everything works ok. But as the ref manual says, when VBUS is present this task is ignored.
Is...
Hi,
We are working on the nrf5340 and our current device firmware uses the NCS 3.0.2 (i.e. nRF Connect SDK 3.0.2). We wanted to try an upgrade to NCS 3.2.1 and followed...
Hi, so my intention was to test the free subscription of Memfault with the thingy91 I created my account in nRF Cloud but the button to access Memfault is not there, I had...
In the documentation , it is stated:
The SAADC is preceded by a gain stage which has a programmable gain. The voltage range seen at the input of the gain stage is:
...
Hi,
We’re looking for the SBOM and the official CPE identifier for the Nordic nRF5 SDK, specifically version 15.3.
We would need:
The SBOM for nRF5 SDK v15.3
The...
I am using the nRF52840DK with nRFConnect for VS Code. In Lesson 6 Exercise 1, I connected the DK to a BME280 board I purchased online. The board exposes the four pins needed...
I've been wrestling with an issue whereby I attempt to deploy an mcuboot image to a device and inconsistently I get a message that says the firmware image is not valid (error...
I am currently encountering an issue with BLE bonding logic in my application.
When a phone initiates a pairing request and triggers a pairing pop-up, I use the security_changed...
We have a custom PCB with a nRF9151 implementation supporting both LTE/NB-IoT and GNSS. The PCB has no switching regulators or any other possible noise source except for the...
