I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
I read this post with great interest!
devzone.nordicsemi.com/.../
I'm having a similar problem with my Nordic Beacon application. I followed the advice to switch my...
I am using a nRF51822 to send data to an iOS device.
Because latency is critical to my application, i 've set up a test program that sends a packet every second , using notifications...
I have some questions about the scan response packet.
Can a scan response be sent with a peripheral that is configured to be connectable? IE not a beacon.
I read...
Dear Nordic Team,
Thanks for support.
I am using nRF5_SDK_11.0.0. How can i initialize the softdevice with internal RC oscillator in my source code. I am using the below...
Hello;
I'm trying to get data over the TX pin to be sent to the RX pin on a Raspberry Pi.
I have it working on several boards: The nrf51822 Development Board, the Redbear...
The radio notification tutorial ( devzone.nordicsemi.com/.../) says:
"The distance is the time window before/after the radio goes active. The radio events are radio_on...
I'm slightly bamboozled by the LFCLKCSRC options in the NRF52 datasheet / product specification.
Bit field SRC makes sense. Set to 0 for the internal RC oscillator, 1 for...
Hi
I am currently using the boot loader from SDK7.2.0, compiled using Keil.
However, for all the other software I am using GCC. But GCC support for the boot loader was...
Hi, i am trying to send my notify characteristic every 100 msec, i am using timer for this and when i am connecting to the nrf app, my nordic device is sending the data but...
Hello,
Thanks for your reading.
I tried to read the CHIP_ID value(0xD1) of BMI160 in MetaWearCPro firmware using SPI.
But I could not get the correct value(0xD1). The read...
Hi, I use the following.
Raspberry Pi 3 (RPi3 with Raspbian Jessie 4.4) as a router,
RPi3 is connected to a Wi-Fi router to access the Internet by using the built...
My development Kit is official PCA10040, and SDK is SDK 11.
when i opened the keil project of ble_app_multirole_lesc int the examples of SDK with Keil MDK5.14 and compile...
Hi,
I've got a nice, well-documented bug here:
github.com/.../25
The short of it: Adding a single printf() statement to this mbed OS example causes my nRF51-DK board...
Hello all I am new Nordic and Bluetooth, before starting my project I did small experiment to understand the system i did the following steps.
Used nRF51822 -32 KB...
