Hi,
I have a system I am redesigning to use the npm1300.
It has a rechargeable battery, about 3-4 weeks per charge, connected to an nrf9160.
The current system...
My GPIOTE input seems to stopped working when migrating from NCS 2.5.0 to 2.7.0, so I decided to downgrade to 2.6.0, and it seems the issue is still there. When migrating...
I'm running into this issue quite often where I have a Build failure. I'm sure to others the way to troubleshoot what the issue is may be obvious, but being fairly new to...
Hi,
I cannot bond to NRF5340DK running the `peripheral_ancs_client` sample if external oscillator configuration is disabled (thus using synthesized from HFCLK).
Environment...
Hi,
We are working on nRF5340 with TF-M enabled and iOS application.
What we are observing is the peripheral device MTU TX and RX are configured to 512 bytes whereas the...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
hi support team,
in 9161dk, when we need to program external flash, we need to config board with nrf connect, may i ask what's this? and if i need to consider power consumption...
We are currently getting our firmware ready to test devices for FCC and other radio testing. We have an AThost-like setup that passes AT commands from a terminal over a BLE...
.Hi Nordic Support team,
I'm using NRF52832, SoftDevice S132, SDK version is nRF5_SDK_17.1.0_ddde560.
I want to transmit 9 bytes of data collected from an I2C sensor...
Hi,
the I2C burst write function below work perfectly <16 number of bytes. Once I transfer more that this, the return code throws an error "-28" and my scope doesnt even...
Hello, I would like to develop an automated tool for our production line to use to perform DFU on our nRF52832 system. Is it possible to communicate with the nRF52 Dev kit...
Hi, I developed a custom board and I am able to toggle other IO pins but somehow pin 10, 9 wasn't working. After some research, I found that NFC must be disabled to make it...
Hi,
I am trying to set EDRx en LOG_INF the result using following code:
static struct lte_lc_edrx_cfg drx_cfg ;
//enable EDRx
LOG_INF("== Setting EDRx =...
Hi,
I have a custom board with a nRF52840 and the nRF21540 FEM. To control my FEM, I have added the following to my code to my nRF52840_nRF52840.dts file:
/ {
nrf_radio_fem...
Hello Everyone. I tried to run the ble_app_multirole_lesc example on SDK 16.0.0 to test the numeric comparison match feature on bonding. And found that the handling of this...
Hello,
I am currently updating from SDK v2.3.0 to v2.5.2 but I am not able to get the 'psa' functions working correctly (as they did with previous SDKs).
I am trying to...
Hi, How to find out what function is being called, when sw interrupt occurs? I have created a timer that should call a function. But I'm having a hard time finding what function...
Hi,
I am working on custom board which has nrf9160 as modem and stm32 as host controller.
here I am used lwip stack on stm32 controller to get the IP address.
I have...
I'm trying to integrate AES-128 (ECB mode) decryption into my project
I've based it on the AES_CBC sample, and adapted it to use ECB mode instead of CBC. When I compile...
Trying to use the nRF Connect quick start with the evaluation board and the programming fails. 2024-05-22T09:09:27.145Z INFO Initialising nrfutil module: device 2024-05-22T09...
Hi,
I encountered an issue from my custom board who are using a nrf52832.
When i place my board in very cold temperature environment (around -35°C), sometimes the voltage...
Good afternoon,
I am trying to use a function generator to send a sinusoidal function to my nRF7002 DK and I am vizualizing the values in Putty. I am sending with a frequency...