Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
Hi Team,
I am working with nRF5340 and have a few clarifications regarding SWD protection (APPROTECT / ERASEPROTECT).
While the application is running, is it possible...
We have an unusual issue.
We are using the nrf 17.1 SDK for a custom board with the nrf52840 in tickless idle mode (RTC1) - using the available port_cmsis_systick.c for...
Hi there
I'm using the HCI UART bridge from NCS v3.2.1 in zephyr/samples/bluetooth/hci_uart with the provided overlay-all-bt_ll_sw_split.conf on an nRF54L15Dk and our Bluetooth...
This is just a request for an update to some documentation.
If you do a web search for "nrf NSIB" the first page this is likely to show up is this one . It's a good page...
Hi devzone team I'm working on the nRF54L05 with the FEM RFX2401C from Skyworks. I'm trying to configure the FEM with the "Simple GPIO" option. Here my overlay file:
After...
I have a problem which seems similar to this one: https://devzone.nordicsemi.com/f/nordic-q-a/106158/zephyr-os-ble-central-multiple-notification-subscription-event-issue ...
I'm using the peripheral_lbs sample for testing with the PPK2 kit and the 1.0.0 nRF54L15-DK.
I have disabled logging and serial and added PM_DEVICE and PM_DEVICE_RUNTIME...
I don't know if there is a bug in either nrf9x_socket_offload_close , nrf_close , or our usage of the modem.
It seems to be that if we power off the modem and deinitialise...
Hi,
Having developed for the past several years with Nordic's legacy library, I'm attempting to get started porting my project to Nordic's Bare Metal SDK.
I managed to...
Using the nRF9151 with nRF Connect SDK v3.1.0 and modem firmware 2.0.2 , we're seeing an issue where the modem works fine for days, then it is suddenly unable to open any...
Hello DevZone Team,
I would like to express my appreciation for the excellent support and the collaborative community platform you provide for nRF developers.
We are currently...
Hello! I am trying to compile hci_ipc sample for raytac_mdbt53v_db_40 board (using nRF SDK v3.2.1) and getting the following error: The sample compiles fine for the nrf5340dk...
I noticed on my custom PCB that pairing stopped working, and was getting "reason 0x13" as the disconnect. This disconnect reason I believe is from the phone disconnecting...
Hello everyone,
I’m working with an nRF52840-based board (XIAO form factor) and facing an issue related to USB enumeration and DFU mode detection during development.
Board...
