Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Dear Staff,
we have some Ublox C2909 TAG based on your nRF52833 chip.We need to program them for an RTLS project.
In particular we need to:
customize the FW here ...
Hello,
I managed to run the examples for nrf54l15 channel_sounding_ras_initiator.c and reflector on my custom hardware boards. I changed the overlay files to use my own...
Hi,
I'm working on enabling APP Protection while successfully executing below code:
if (!nrf_sdh_is_enabled()) { if (VERSION_BUILD <= MAX_RELEASE_BUILD) { NRF_UICR-...
Dear all,
I'm using and nRF51822 chip for implementing a wireless HID device with dongle.
The device has an RGB LED, and indication scenarios for different modes are played...
I'm using SDK 15.3.0 example twi_scanner with Segger Embedded Studio. I do a search entire solution for TWI_SCL_M and the only location it shows up is in main under the twi_master_init...
I'm having this issue with oldish SDK 12 but since I reproduce the issue with SDK 15: I re-used the code from https://devzone.nordicsemi.com/nordic/short-range-guides/b/software...
Hello,
I am using nRF5_SDK_15.2.0 and with s132_nrf52_6.0.0_softdevice
I am trying to interface with external Flash (MX25l64) using SPI.so when ever i am trying to send...
Hi
Any sample or known project that can transform nrf52 usb dongle and be driven through COM port?
Imagine a C program in Linux that opens the USB port where dongle...
Hi,
I'm developing a custom board based on nrf52. Currently, we are using Segger through J-Link to program nrf52 DK.
As for my custom board, I left a 2x3 pinout including...
As unicast address is a address of a element in a node.
We have to assign unicast address to 500 nodes each contains 2 elements, and we configured publish and subscribe...
Hello,
I am using nrf52832, having SDK 15.3.0 in Segger Studio IDE. Win10
I am using fds_test_find_and_delete() function, to find and delete particular record from flash...
I latest firmware and loaded and software thingy91_ltem_v0.2.2.hex. And I get reboot all the time. It was working when I first got the kit then when I was testing this weekend...
Firstly, I am a very beginner in the BLE domain. I have very little knowledge of it.
I want to do a project where multiple BLE peripheral devices(nRF52) will communicate...
Hello:
I have questions about eSIM card.
As we know, GSMA standard eSIM card is an empty chip, we can use eSIM card after ISP information is installed into eSIM card....
Hello,
I have the same question as mentioned in this article:
https://devzone.nordicsemi.com/f/nordic-q-a/19252/how-to-avoid-interrupt-handling-is-not-missed-with-sd_app_evt_wait...
Hi,
I use nrf sniffer to monitor BLE communication. After pairing with encryption, wireshark indicates Encrypted packet decrypted incorrectly (bad MIC).
I think there...
I configured Uart on 23 - Rx and 24 - Tx of NRF52832.
In simple uart example it works fine with uart_event_handle for rx.
But when this code is merged with Nrf Mesh Dimmer...
