در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi
I have done multilink with uart and getting data from multiple ble_uart peripheral. now i have to read data from only one peripheral . what will do for that.
I am using...
Hello
I was wondering if there have been any changes in supporting IAR for nRF Mesh?
In your answer from about a year ago you wrote that you were not currently planning...
Hi,
I have some questions:
1. How does the process of getting addresses to the Nodes happen in Mesh stack? Is it automatically or I need to set it when I flashed the...
Trying to run the "Alert Notification Application" example in nRF SDK v15.3.0 on either a Windows 10 system or a Ubuntu 18.04 LTS system. Following the instructions, I can...
hi,
i want to use mesh network in my project.our requirement is multiple nodes will be sending data to one master node.is there any example code.
Regards,
jagadee...
Hi,
We have a gateway device that contains the nRF51822 MDBT40 Raytac module.
We are designing a new nRF52832 based sensor and we want to connect 20 of them to the Gateway...
I use nrf_drv_saadc_init(NULL, NULL) to sample AD per second(Blocking type).
But every time the firmware runs, the ADC value always takes several times to stabilize.
...
when trying to initialize the nrf52...little bit confused how to specifically address a pin for i2c....can anyone help me with a piece of code.
Thank you in advance.
Hi. i'm using IAR and St-link to program the nRF52832, and run this tutorial on my custom board, but the Bluetooth has not been set up by the method that you proposed. and...
Hi guys, I have a question about ble_app_uart_c example in SDK. (I'm using the latest SDK, 15.3)
And my board is nRF52 DK, which is PCA10040.
While I'm testing ble_app_uart_c...
Hey everyone,
i would like to use the NRF52811 with the new Softdevice S140 V 7.0. Therfore i took the ble_app_blinky (pca10056) example and changed some preprocessor...
I am using parts of the ANCS example code within a product near pre-production. I am able to reproduce the problem in the ANCS example without modification. Here are the specifics...
Hi,
we are using nRF52832 for beacon application. we want to find the low battery condition.
Does nRF52832 have option to read the voltage level? if so please share api...
Hello,
I have created a custom board that uses a NRF52840.
From my understanding, i'm need only VDD,GND,SWDIO and SWCLK connected to the SOC to flash them by using an...
