I downloaded NCS 2.9.0 from nRF Connect For Desktop and sdk-sidewalk following Nordic's instructions. After successfully downloading everything, I built the sample "Hello...
Hello,
We have implemented and tested the scanner code for the nRF52832. Now, we want to migrate the same code to the nRF52833. The project has already been configured for...
Hi，
I ran into this error:
00> <error> nrf_ble_gq: SD GATT procedure (1) failed on connection handle 0 with error: 0x00000008. 00> 00> <error> app: ERROR 8 [NRF_ERROR_INVALID_STATE...
hello nordic, we are looking at nrf52820 to satisfy some requirements. 1: We plan to power off single cell Lithium application which can be 2.7V - 5V trhu VBUS / VDDH and...
I am attempting to generate an 8MHz clock output on pin 2.05. I've followed an example from another post using the nRF54L, but I get build errors. The project I used as a...
Hello,
We struggle to keep LTE-M attached with nRF91 (Modem) and CMW500 (EPS) to test regular IP communication (so those are not Radio Access Network tests) during product...
Hi everyone,
Could someone help me with the following use case?
Task description: I'm working on a firmware update procedure based on the smp_svr project. I'm trying to...
Hi ,
I am working on a NFC project which has below requirements , could you please help check if we have any existed example I can test ?
1. Support standarded ISO/IEC...
I'm looking for a nodified 'Wireless UART example" that I can use for a range test.
https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.3.0/wireless_uart_15_4...
Hello,
I have problems using nrFgo Studio with my J-link programmer. The "nrf5x Programming" section is greyed out when the j-link is connected to the PC and the MCU....
I am working on a client to collect data from a continuous glucose monitor. I see that the CGM Service has been part of the SDK for some time. But there is no matching client...
Hello
I have nRF52840-DK and also a nRF52840 Dongle with me and i have installed SEGGER Embedded Studio with "nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71" SDK downloaded...
Hi--
On dev kit PCA100056, SoftDevice s140, SDK 15.3, in project ble_app_uart_pca10056_s140, we are trying to operate the UART TX/RX characteristic with outgoing payloads...
Hi All,
I'm very new to this Bluetooth mesh technology. Currently I'm referring to client/server switch example.
Without making any changes in the firmware I compiled...
I am seing odd time strings from AT+CCLK... Like: "+CCLK: "15/02/01,00:00:08"\r\nOK\r\n"
I think it is required that AT+CCLK responds error until it has gotten network time...
Hi!
I work at Lund university and I'm preparing a upcoming course project course. The course is about prototyping and PCB design. I want to use the nrf9160 as a example...
I get FDS_SUCCESS after I do fds_write(&desc, &m_dummy_record).
But when I do rc_read = fds_record_find(FILE_ID, REC_KEY, &desc, &tok); I get an error code rc_read = FDS_ERR_NOT_FOUND;...
Hi all,
I am trying to develop an Android app to connect to a nrf52832 running the ble_app_uart example. Previously I was using the Android-nRF-UART codes as a starting...
Hello
I have nRF52840-DK and also a nRF52840 Dongle with me and i have installed SEGGER Embedded Studio with "nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71" SDK downloaded...
I'm having a frustrating time trying to enable UARTE1 to stream fast ADC results to a terminal.
I believe I have edited sdk_config.h correctly, but looking at nrf_serial...
In continue to https://devzone.nordicsemi.com/support/233777 We tested the demo for some days, it works. But last week it stoped on open socket with error -47. At the same...
