Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hello,
I managed to run the examples for nrf54l15 channel_sounding_ras_initiator.c and reflector on my custom hardware boards. I changed the overlay files to use my own...
Hi all,
I want to fully understand the concept of Bluetooth protocol using nrf52811. Any advice will be helpful for me!
First, as I understand softdevice is Bluetooth...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
Hello,
We are working on establishing a connection between one of our existing Bluetooth modules (cypress) and nordic based module to provide backward compatibility with...
We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
We use several Nordic chips in our BLE sensors. We bond to the devices from Android, connect to update configurations, then disconnect such that the device then advertises...
Hi,
I`m using MDBT50QRX (Raytac Nordic 3rd party for modules) I need to connect and program the firmware hex file (connectivity_4.1.1_usb_with_s140_6.1.1.hex) which is on...
Hi,
Intention:
I want to build and run a sample application without suggested IDE on my custom nRF52811 PCB.
Previous steps:
Based on a tutorial [1] I found I was...
Hi,
I successfully tested ecdh and aes256 in seperate projects but I want to combine them.
This is my code:
Problem is that when i call the ecc functions this happens...
Hi, I'm using nRF Mesh App to provision more than 5 devices for vendor specific models other than on/off model. My purpose is to send some data instead of on/off the light...
Hi all
I am using a nRF52840 with SDK 15.3.0 and s140_nrf52_6.1.1 soft device.
My application is a multi-peripheral device that has a common service, each peripheral can...
Hi
I'm really new to this, forgive me it's a stupid question. I'm using the nRF52 DK from Nordic.
I started with the "Developing with SEGGER Embedded Studio", but when...
In the user manual of nrf52832 it is said that ram[n].power are retained registers in sleep mode and that depending on the settings.
One or more RAM sections can be retained...
Dear Nordic DevZone Team, With ARM cortex M4, it is possible to go into deep sleep mode. In the Nordic nRF52832 which uses M4, it is configured for BLE advertising. I would...
Hi
I read nRF52840 - LPCOMP information on datasheet and SDK.
It shows VHYST value is 35mV (typ.) in datasheet page 191 and 50mV (typ.) in SDK - nrf_lpcomp.h.
which...
Hello,
In addition to previous ticket I have further queries. I have a stringent requirement for reduction of Current consumption.
https://devzone.nordicsemi.com/support...
Hi, I've got a quick question here about using the GPIOTE driver in tandem with the GPIO HAL . For simplicity's sake, I'm using an in-house library that gives me high-level...
I have been encountering a rather latent bug in a product that we are developing. It consists of a custom nRF52832 board, that is connected to an nRF52-DK via ESB, and the...
Hi
In eddystone when we connect the beacon in connectable mode then it start non connectable advertising automatically without disconnect, same time we can change parameter...
How to send some data from light_switch_server node to light_switch_client node in the mesh sdk examples of the new version mesh sdk 3.1.0?
I basically want to send data...
Hi everyone,
I made a custom pcb and it has nrf52810. I want to flash it using by nrf52840 DK.
This is my connection ;
My Board(nRF52810) -> nRF52840-DK
SWDIO -> SH_SWDIO...
