Hi,
I'm using the nRF54L15 DK (non-secure, NCS v2.9.1) to generate a 100 kHz PWM on a GPIO with TIMER00 (128 MHz, 1280 ticks, 2.5%–20% duty, 32–256 ticks). GPIOTE, DPPI...
Hello everyone,
I'm working on a project based on the nRF52840, and I'm using nRF Connect SDK 2.9.0. The project uses MCUboot, but the firmware image is signed externally...
Dear nordic team,
even if enabled for mcuboot via CONFIG_WATCHDOG / CONFIG_BOOT_WATCHDOG_FEED, our device performs a reset when swapping the image. More precisely: when...
Hi
I remember the Devzonw could ask for hardware instructions. My matching circuir has used the nRF54L15 reference design and nRF21540 DK design, all the value is the same...
Hi,
I'm testing the nrf_provisioning sample application.
I have built it with the coap overlay.
After claiming the device in the nrf cloud and assigning the " nrf-cloud...
Hi,
USB CDC EPOUT stops working as the USB incoming traffic data rate increases. The symptoms of this issue align with the Errata 199. The workaround for Errata 199 is...
Hello,
We’re testing the nRF9160 GNSS performance on our custom PCB and have noticed that, even with A-GPS, the first fix after powering on the device takes significantly...
NCS 2.8.0, NRF52840 with accurate crystal LF CLK
I've been asked to tightly synchronize timestamps for data collected by external sensors on multiple boards. The timestamps...
seems like all packs cannot be downloaded from Keil 5. all address are invalid, include all examples.
The requested URL /nRF5_SDK/pieces/nRF_DeviceFamilyPack/NordicSemiconductor...
Issue:
The OTBR could run with RCP versions built with SDK v2.3.0 and v2.4.2 but couldn't work with fw from SDK v2.9.0. Hence, I wanted to know which of the latest SDKs...
I have been working on a project using a nrf52832 and currently have the firmware developed on nrf5sdk. I have been testing out Zephyr with this example https://docs.nordicsemi...
Hello
I'm using the NRF52840DK with a custom shield on top that interfaces to my custom board. I use it to program and debug the DUT via the DK, talk to the DUT over serial...
Hello,
I am working on an update of older FW implementation: nRF52832, SDK 14.1.0, with SoftDevice S132 and using BLE connection.
The change I need to implement is a functionality...
Dear Nordic Technical Support,
I’m currently evaluating the NFC functionality on the nRF7002-DK with the following setup:
Hardware: nRF7002-DK
SDK Version: nRF...
For power-saving we periodically enable/disable the net-core. We would like to use the WDT on the net-core
as well. Since you cannot stop the WDT, how should we handle this...
When I first set up my system I had a color code view of the RAM in my system where the colors corresponded to grouped data objects. Somewhere along the line that view has...
Hello,
I am unable to use the Segger RTT terminal built into the nRF Connect SDK for VSCode Extension pack with the nRF54L15DK.
I have configured my project with the...
Hello,
zephyr: Vanila v 4.1.0
I'm trying to run FOTA via BLE on the nRF54L15DK. I’ve configured everything as it should be, based on the sample:
When I...
Hello,
Is it possible to make the nRF Sniffer for Bluetooth LE application work on a nRF54L15?
https://www.nordicsemi.com/Products/Development-tools/nRF-Sniffer-for-Bluetooth...
Hi, I am testing the PaWR examples in the NCS and I have few doubts.
In this page , it says in section 1.3 that there are two ways for synchronization - PAST after connection...
From what I can see in the documentation, UART0 is used by default for "non-secure" / application logs and UART1 is used for "secure" app logs. I am needing to interface with...
Hello, I am using an I2S PDM Mic and trying to send the I2S Data over BLE using Segger Embedded Studio. The I2S Program that I have generated is working ok. I have verified...
