Hello,
We have implemented and tested the scanner code for the nRF52832. Now, we want to migrate the same code to the nRF52833. The project has already been configured for...
Hi，
I ran into this error:
00> <error> nrf_ble_gq: SD GATT procedure (1) failed on connection handle 0 with error: 0x00000008. 00> 00> <error> app: ERROR 8 [NRF_ERROR_INVALID_STATE...
hello nordic, we are looking at nrf52820 to satisfy some requirements. 1: We plan to power off single cell Lithium application which can be 2.7V - 5V trhu VBUS / VDDH and...
I am attempting to generate an 8MHz clock output on pin 2.05. I've followed an example from another post using the nRF54L, but I get build errors. The project I used as a...
Hello,
We struggle to keep LTE-M attached with nRF91 (Modem) and CMW500 (EPS) to test regular IP communication (so those are not Radio Access Network tests) during product...
Hi everyone,
Could someone help me with the following use case?
Task description: I'm working on a firmware update procedure based on the smp_svr project. I'm trying to...
Hello,
I have made a project that was based on the nRF9151 Development Kit and it works great. I had to select the -ns configuration to get anything to ever build and now...
Hi Nordic,
I am trying to do a time critical data acquisition in a BLE based application.
Earlier I was using software timers. But, since the software timers are not accurate...
Hi all, I have some question for ask :
I add NUS service into light switch proxy server example. And I only run nus service part (Don't run Mesh part)
when I use IOS to...
Hello All, Please help me. I have nrf52840 and added json parser which is large and nested. Json_parse fails , is there anyway to enlarge heap size?
Any feedback must be...
Hello,
I'm trying to flash wt51822-s4at using nrf52dk ( https://4tronix.co.uk/picobot2/WT51822-S4AT.pdf)
It has nrf51822 chip on board
The firmware goes through without...
Hi,
Does FDS event handler run within interrupt context ?
Can another FDS api be called from within the event handler (i.e. - calling garbage collector from within event...
I am using a three axis mems sensor and will need to computer trig functions.
If I use the math.h in the Segger Embedded Studio will it use the floating point hardware in...
In this thread https://devzone.nordicsemi.com/f/nordic-q-a/32708/bluetooth-developer-studio-plugin-for-sdk-15-0-0/126066#126066 Kenneth said there were no plans to update...
I can not debug my app with freertos and BLE if the ble is connected, but I can debug the app id the ble is disconnected, i want to debug inside the xqueue recieve and send...
I'm developing on the nrf52840PDK and I was running the cdc_acm exmaple in the SDK to observe the token exchanges between the host and the device.
In the Nordic52840 Product...
Hi all,
I have a module with nRF52832QFAAB0 IC, I'm looking for the IC revision in the compatibility matrix here.
Unfortunately I didn't find any packet variant and build...
I've run the Demo(thingy52-mesh-provisioning-demo). And it works. Now, I want to expand the function.
I 'd like to create more model(for example, sensor model for humanity...
Hi,
Sorry for post here again but i'm having a lot of trumble. I'm actually at the step 4 of the guide, which is the page generation.
I've made correctly all the previus...
I am working on a nrf51822 board and trying to run ble_app_hrs project using nrf sdk 12.1 and s130 softdevice. I converted the uVision project to the Segger Project using...
I use SDK 12.3.0 with IAR
If there is an option to know the last page that programmed?
For example:
Linker: ROM start address 0x1F000 end address 0x76fff
But...
Yesterday, I upload the thingy sdk v2.1.0 in keil uVision5 and rebuild it. After rebuild, it showed one error namely "fatal error" due to the large size(122kb). please suggest...
