I have been testing the HTTP FOTA procedure as documented here using the 1.5.0 test diffs as provided in .
Many of the messages output by the modem in this upgrade process...
While trying to run the FOTA-TEST upgrades from I came across unexpected behavior when the same script fails twice in a row. I first attempt to trigger a FOTA with the following...
Quoted from Heidi’s blog post Target Wake Time on the nRF7002 DK , published 23 Feb 2023 (available at https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/target...
I have nrf52840 DK board, running cutom image that implements BLE central, constantly scanning on coded (S8) phy. Trying to add NFC T2T tag, and it doesn't work. Disabling...
Hi,
We produced the first batch of 10 modules in July 2026. Out of these, 8 modules are working properly, while 2 are not working.
We then produced a second batch of 10...
Title: SoftDevice Controller: 100% connection establishment failure (HCI 0x3E) with SKY66112-11 PA active
Hi Everyone,
I am working on the following development project...
Hello,
I would like to use spi to connect to a ADC on a nrf54l15dk at high speed using DMA.
I want to use nrfconnect bare metal, but cannot find a starting example.
...
I need to port a system from a STM32F407 MCU to the nrf52832.
The old system would continuously poll a SPI slave for 244 bytes of information and after receiving 60 valid...
Hi,
I am working on the ADC and trying to sense the battery level to measure it voltage.
And I have configure the ADC with normal conditions as present in example of SDK...
Hello
First things first, when I use the UART example located in:
\nRF5_SDK_15.2.0_9412b96\examples\peripheral\uart\pca10040\blank\ses
all works fine, the script compiles...
Hi,
I hope this is the correct place to ask beginner questions. I new to microcontrollers in general.
So first of all here is what I am using currently:
Software:
...
Hi,
I'm using Nrf52 with SDX 15.2.
The device is far for the host (smartphone), I would like to know if I can know the RSSI with the Smartphone? How can I control the...
Hello everyone!
I'm trying to implement a mqttsn client inside a microcontroller, and the nrf52840 should be used only as a way to communicate with other thread devices...
Hello!
My name is Tiago Morais. I've started to work with nrf52840 and now I'm having some problems with its CLI.
I'm trying to use the nrf52840 dk with openthread and...
Dear Nordic Team, Thanks for supporting.
Currently i am working with DFU for nRF52810 custom board. I am using SDK15.2.0. I followed these steps (//devzone.nordicsemi.com...
Hi all,
I'm following https://www.nordicsemi.com/DocLib/Content/SDK_Doc/Mesh_SDK/v3-0-0/md_doc_getting_started_dfu_quick_start and I'm using mesh SDK v3.0.0, I have a problem...
Hi all:
All of the example code is using GPIOTE to demonstrate how to handle GPIO interrupt.
However, it just can configured HiTOLow/LowToHi/Toggle.
If I want to trigger...
Works
Use nRF Connect v2.6.0 on Linux to erase, program softdevice.
Works
Use Keil to program application firmware
Does not work:
Use nRF Go studio to detect...
I need to implement a simple uart protocol. most messages are fixed length (8bytes) with some exceptions.
here what I do in pseudo code, I send 8bytes and expect 8bytes...
Hi
I am trying to port an SPI driver from a project for the NRF51822 to an NRF52832 and running into a problem reading more than two bytes. We are using SPI0 (not SPIM0...
Hello,
I'm using an NRF52 DK board.
I noticed that when I change P0.27 from the default (input / not connected to input buffer) to being an input pin connected to the...
Good evening,
I had a question in respect to the exact procedure needed to read a characteristic with read permissions. I have just discovered a service i would like to...
