I am using the 54l10 chip, and after compiling the project, I will receive a hex firmware and a zip update package. The bin firmware and hex firmware in this update package...
Dear Technical Support Team,
I am trying to integrate and run TensorFlow Lite Micro on the nRF5340 Development Kit using the nRF Connect SDK. I have tested both SDK version...
Hi,
I am working with the NRF52832 SoC using the NRF52 DK and developing with NRF Connect SDK version 2.7.0. I have enabled BLE with LBS, BAS, and FUOTA services, along...
Hello, checking if I'm doing this right of restoring initial fw for 91X to work with Quick Start v1.2.0. as described here in Get Started, https://www.nordicsemi.com/Products...
It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
I am testing out the nRF54H20 on the nRF54H20-DK version 0.9.1. I have followed the steps for setup in the "Getting started with the nRF54H20 DK". I currently have nrf54h20_soc_binaries_v0...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi
I would like to connect the nRF52810 to 2 devices via UART interface by switching the Rx and TX GPIO pins by the software in realtime.
Is it possible? what is the method...
Hii
I m using Fanstel Ev board (BT840F) using nRF5248 Fimware.
i want to set maximum transmission power +8dbm in FANSTEL Ev Board but i got an error code 7 is Indicate...
Hi,guys.
In my experiment, Firstly,I creat an app_timer work every 20ms interval
APP_TIMER_INIT(APP_TIMER_PRESCALER, APP_TIMER_OP_QUEUE_SIZE, false); err_code = app_timer_create...
Hi everyone,
Recently, I used the nrf52832 learning board to learn SDK13.0.0, when I see SAADC, tell the truth, this exampe is a bit difficult for me to understand.
My...
Hi
I am trying (for the first time) to deal with flash. Hence, I started by a simple app, without BLE/SD (blinker)
The problem is that, the first API call pstorage_init...
1. Connected to nRFgo Motherboard's nRF ISP and NRF24LE1E SPI pin
[nRF ISP]
[NRF24LE1E의 SPI]
2. In nRFgo Studio, Features> 2.4 GHz is disabled
3. I want to know...
Hi everyone!
My question is for engineers of Nordic. I need to apply NRF52840 as a " beacon ". As there is no ready templates of beacons in nRF5_SDK_13.0.0-1alpha_055eef3...
How to select nrf528332 UART clock source, how to make the serial port baud rate not change with temperature?When the baud rate is 9,600, the baud rate varies greatly with...
i have a problem with ble_nus_send_string function, the BLE_NUS_MAX_DATA_LEN is 20 bytes but i need to send 1kb every second, is that possible? i tried to put ble_nus_send_string...
Hello Nordic Team,
in an application where space and cost is an issue: how cirtical do you estimate the 15nH inductor on the Output of the DCDC? (L5 in nrF51x22 ref-design...
hi
I am a beginner,i have two questions.
1、when i use the nrf52832 to read the inner temperature,i find the nrf_temp_init function is :
static __INLINE void nrf_temp_init...
Dear support team,
Can a Thread Boarder Router have Leader role? I have not seen any document which mention about it but all the Thread topology diagram have independent...
Hello,
I am not able to make the FDS work. Here is my setup
NRF51
SDK 12.3
S130 (2.0.1), i.e. s130_nrf51_2.0.1_softdevice.hex
Using peer manager as well...
We've been using bonding on our device for a while and have a lot of experience there, but we are now attempting to add "Just Works" pairing support that is a configuration...
nrf52832.
SDK14.2
Segger ES V3.34a
I am using nrf_drv_saadc_calibrate_offset() and find the next sample immediately after the calibration is erroneous.
There is...