I am relatively new to embedded and am wondering if there was a "best practices" guide / checklist for production deployment somewhere. Things like making sure you are using...
Hi. I'm trying to write a simple MQTT app. I am consistently getting these KConfig errors to do with variables I'm not using, and I have tried to set CMake to ignore these...
Good day,
I've developed a board with a MDBT50Q on it. I'm using the Reg0 DC/DC and LDO Mode Disabled reference circuit ( https://www.raytac.com/download/index.php?index_id...
Hi,
I have the issue that my Zigbee device reports the error "Production configuration is not present or invalid (status: -1)". I followed the guide from this( https://docs...
Hi,
I am using an nRF52840 as a Zigbee NCP. I have built the firmware myself using nRF Connect, and I am also running MCUBoot. Sometimes after some usage, the chip starts...
Hello everyone,
I am testing out I2C on the nRF54L15 for a custom PCB project.
I first tested a simple mpu6050 sensor on &i2c21 on pins P1.11 for SCL and P1.12 for SDA...
I have a bit of an unusual use case where the nPM1300 is quite ideal but need to use an external charger for the battery instead of the internal charger. The nPM1300 fuel...
Hi
I am working on a firmware which can be used in serveral custom boards. While it works perfect in old sdk, I met the following problem when migrating from Sdk 12.2 to...
Hi,
I have tho following configuration: SDK 10, S110 and I'm using Segger Embedded Studio, single banker dfu.
I am able to program DFU and buttonless DFU; However, when...
Hi all,
I am using PCA10040 with nRF5_SDK_13.0.0 and using the ble_perpheral -> ble_app_uart example.
I am trying to stream data from UART to an android phone and the...
Hello,
I've been using the new power profile kit and I seem to be getting only 3 volts output as opposed to the previous versions where I was getting about 3.6 volts. How...
I was checking out the serial example using two PCA10040 evaluation boards. Most of the commands were executed successfully as mentioned in the link http://infocenter.nordicsemi...
Hi,
I'm developing a node based on the nRF52840-QIAA rev. B.
I'm using Eclipse Neon and GCC-toolchain for coding. Softdevice is S140 5.0.0.2 alpha and SDK is V14.2.
...
Hello,
I would like to be able to sample an analog voltage signal with a sample rate of approximately 250us (4096 samples/sec). I am using the SAADC example in nRF5 SDK...
We are trying to use nrfjprog.dll in a c# program to help us with manufacturing and quality assurance.
We are able to load and call the functions from c# and all the functions...
Hi! One of the designs still has the internal RC for the low frequency clock. Hardware and software turns out to be working okay, where system off current is ~0.4uA and sleeping...
Hi,
our BLE device has a hard current limit around 1mA. This is no problem as long as the BLE central behaves as "intended", e.g. iPhones use mostly connection intervals...
Hi All,
I am just play with nRF52 SoC.
We design small wearable device based on MDBT42V BLE module with nRF52832 chip inside. For lear we have nRF52 DK.
I work with...
Is there a way to erase/format everything that is stored in FDS so the storage can be reset to a blank state?
I wasn't able to find away to enumerate all files stored in...
I just updated the latest SDK in keil.
Now I am getting this error.
softdevice_handler.c is v2.0.0-2.alpha
Line 388:
p_ble_enable_params->common_enable_params...
Hi,
I'm missing something on how forwarding interrupt control between SoftDevice and APP works! how is it that part of the interrupts are handled by the SoftDevice code...
