Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hello all,
I would like to establish connection between single central and two peripherals for bidirectional communication. I edited ble_multilink_central example and created...
I and new to programming the BLE devices and have just started out on the nRF52840 PDK and using Segger Embedded Studio for ARM v3.34. I have compiled and downloaded the ble_app_template...
I have to question:
1: if customer use relay node for mesh net, how much is the power consumption for one node? is there any passable to declare the power consumption to...
Hi,
I need to measure the capacitance of few capacitors for which I am currently using 3-channel CAP1203 IC from microchip.
However, I just came across the possibility of...
Hello,
I would like to establish bidirectional communication between single central and two peripherals. I referred ble multilink central example and made corresponding changes...
SDK： nRF5_SDK_11.0.0
Softdevice： s132_nrf52_2.0.0_softdevice
I set the WDT timeout in the application is 5s, when entering the BootLoader set the WDT time is 10s, how...
I am new to ble programming.
I am trying to find the best way to send json objects from android app to nrf52 chip.
What is the best way to send the json object to the...
Hello Sir,
I have developed small and compact product using nRF52832 Soc. Due to size limitation and device is portable. I have attached snap shot of power supply circuit...
Hello sir,
I am develop us product using nRF52832 chip on DK board use S132 soft device and its working well fine. So now we are designing hardware PCB of my product for...
Hello, I am trying to use adc with the uart so i can monitor the readings from adc. But when I include both drivers (nrf_drv_saadc , nrf_drv_uart) i got a confliction error...
Hello, although i have included every library and c file that is needed. i still get a declaration error. I'm almost sure that i enabled everything in sdk_config . I'm kinda...
In sd_power_system_off()，the nrf51822-board current is 2uA；And I think the current in sd_app_evt_wait() will be ~4uA(Is it correct)?
In sd_app_evt_wait(), the code...
In this example project
nRF5_SDK_12.3.0_d7731ad\examples\ble_central_and_peripheral\experimental\ble_app_multirole_lesc\main.c
/**@brief Function for initializing...
Hi,
I am trying to migrate to SDK14.2 from SDK12.
I have succesfully migrated to SDK13, but I am seeing linker issues with 14.
The linker comes with the following errors...
Hi
I am new to BLE. I try to use Dongle + Master control Panel as a peer device. I follow this tutorial application: devzone.nordicsemi.com/.../
I try to flash program...
