Hello, I just try to migrate our developing project from old parent-child build to sysbuild,
But when I build the project with non-secure cpu (with TFM), I get the <err...
Hello, the CTE signal for Bluetooth AoA (Angle of Arrival) positioning is primarily transmitted over BLE advertising channels (37, 38, 39), corresponding to frequencies of...
:
I have seen three folder in the Thread lib path, there are: ftd, mtd, master.
I have some questions below, looking forward to your answer:
For FTD, are both cli...
Hi, I am using two nRF54L15 DKs running THroughput samples.
The result of coded s8 is 52kbps, which is close to the theory number.
When I change to S2 code, the result...
Hi,
I was wondering if the newest sample available in NCS3.0.1 is already capable of holding multi connections. Otherwise, for this little time that is present i will...
Dears,
I have tried to install the nRF connect SW package on a Windows 7 32 bit system (different versions) but was not able to get the applications running. When installing...
Hello, I'm running an example of channel sounding using nRF54L15.
The build is fine, but the following error occurs during flash.
Python is using 3.12.4 version. As you...
Hi,
Is there any other define to change than SERVER_COUNT in main.c of client's light control in order to run the example with only 1 client and 2 servers (instead of 3 servers...
I cannot get the output from the is the example the UART buffer gets filled but there is no output to the tty.
The interrupts seem to be set, but I don't see the interrupt...
Hi
I am using nrf52840 for indoor positioning application based on RSSI. I was wondering if somebody has a tip how to calibrate the nodes before doing the experiment.
Hi,
I'm using sdk12.3.0 ble_app_uart.
My problem is BLE connection.
Sometimes(almost 50%)I tried to connect BLE but fail and I have to connect again.
I don't know...
Hi, I'm contemplating ways to drive a small RGB LED matrix with the nrf52832 in a really space-tight project. Ideally without any external components. I'ts maybe around 40...
Hello,
I need do synchronize the time between two NRF52 devices. One is connected to the other by a custom BLE service. Do you have any ideas how this could be done?
...
I'm trying to integrate buttonless DFU with secure bootloader with bonds with the DFU.
Using SDK 14 with SD 132 v5.0.0.
Using projects: secure_dfu_ble, ble_app_hrs_freertos...
Hello:
When I try to open an example project from nordik, keil doesn't open some files and I get the following error:
"no source": Error: #5: cannot open source input file...
in main() I initialize the timer
// Initialize the clock module
ret = nrf_drv_clock_init();
APP_ERROR_CHECK(ret);
// Request the low-freq clock to start N/A for SoftDevice...
SDK v12, SD130 on 51822.
I init uart through APP_UART_FIFO_INIT, and installed uart_event_handler. UART rx/tx with an external MCU works OK while softdevice running.
...
Hi. I have some nRF51 firmware I'm migrating to the nRF52. It's a peripheral with bunch of vendor specific services, using SDK 13.0.0 and SD 132 v4.0.2.
My code builds...
Dear Nordic,
I am trying to send the sensor data via beacon. I am regularly updating the manufacture data (through which I am sending the sensor data). But while executing...
In fact,there is a demo on internet, and I test it ,but I found that the event is not reliable! my code is :
static void my_fds_evt_handler(fds_evt_t const * const p_fds_evt...
After some effort, I have managed to build the beaconing example that's missing from the examples.emProject of the ble_mesh_v0.9.1-Alpha SDK. I have this running on the PCA10028...
