Hello,
we are using a nRF5340 with NCS 2.9 and want to signalize a
UART_LINE_CTRL_BREAK
on USB CDC_ACM to the PC.
Is there a direct way to do this?
Many thanks in...
I am analyzing the power consumption of a custom board with an nRF52833 BLE SOC and nRF21540 FEM for different BLE parameters. In one of my experiments I vary the amounts...
Hello, I can commission bulb and switch pass, then I refer this link( acl and bind ) to write ACL and binding both, eventually I can use switch to control bulb!
But I have...
Hi,
I'm using an nrfx_timer event with k_poll_signal_raise to trigger a thread to perform an operation.
I've noticed around 900ms delay between when the signal is raised...
I have a LIS2DW12 accelerometer connected to nrf52840 SPIM3, and I am seeing an intermittent failure. In some instances while collecting accel data during a data ready interrupt...
hello Nordic
i am working with nrf52840 running ncs v2.8.0
this device connects with a central, via BLE, the central running on linux.
i am working with smp (simple...
I’m using nrfjprog version 10.12.1 and JLinkARM.dll version 6.88 . I encountered an intermittent nrfjprog error when programming firmware to the nRF52833 .
In most cases...
The debugger does not work with the latest GNU toolchain for ARM Cortex-M build. It throws the following error on Eclipse:
Could not determine GDB version after sending...
GPIOTE Library makes my Board(nRF51422-QFAC) Brick??
I just build my nRF51422 Board, and It's pretty working well before I've used GPIOTE Library.
Before using GPIOTE...
Hi everyone,
I am seeing an issue where the SPI (master) ignores the first byte of RX buff and begins storing the received bytes from RxBuff[1] instead of RxBuff[0]. In...
Does anyone know if there is any documentation of nrf51822's current consumption? Perhaps, something similar to CC254x's Application Note . I'm mostly interested in the current...
Hello,
I would like to build two boards that can send small messages between them, at long distance. For that I would like to use some of your devices (I used 51822 in...
Hi
I have working module which communicates via uart with another module. It works good, unless it is heated to 40C. After that temperature UART communication is not correct...
Hi Engineers!
We made our own ten (10) PCB's with nRF52840 MCU onboard fully according to "Circuit configuration no. 3":
1. LDO only mode (VDDH connected to VDD connected...
I have a custom circuit with nrf52832 which I am trying to program.
All i/o pins seem to be working fine except pins P0.06 - P0.10.
I'm testing it with mbed (digitalout...
Hi,
Thanks for taking the time looking into issue.
We are using Keil uVision 5.14.
Our target is a custom board (BMD200 eval Module based on nRF51822)
We were able to...
Hei guys,
for a new custom board based on nrf52832 where i have to minimize power:
have an external Li-Po battery, with a cutoff @3.0v, so the range will be 4.2v...
blesc_pairing_dhkey_check_failed.zip
Hello,
I used the example ble_app_multirole_lesc and paired with nRF Connect app. However I got the error message (in Bluetooth...
Hi!
So I have my GATT value of a service that I would like to update.
Sadly that value always stays at the initial value.
Below you can find my update function.
uint32_t...
I am using SDK12.0.0. ble_app_uart example, and I have change the clock to using LFCLK RC. I know from nRF51822-PAN_v3.1.pdf that we need to calibrate the LFCLK RC after reset...
I've managed to overcome all the quirks in setting up Eclipse/gcc development with the nRF52 PDK (PCA10056), and I can build the sample projects just fine. Here's my issue...
