Page 399 of nRF54L15/nRF54L10/nRF54L05 Datasheet v1.0 shows:
CLK = PCLK32M/(2*PRESCALER)
but this formula does not match the values in the examples in Table 46.
I CAN...
Hello Nordic Team,
I am currently working with the nRF52832 on a custom board using nRF Connect SDK v2.9.0. I am implementing OTA DFU using Sysbuild and MCUboot with an...
Hi Team,
I am working on OTA using an external Winbond flash IC (W25Q64) with the nRF52832 controller in NCS SDK version 2.9.2. I have completed all the required configurations...
Hi team,
We are going to kickoff a new project of 2-mic AI recording pen. Good to see we got a very high performance for 54LM20B with DSP/NPU, which might be a very good...
Hello,
We are currently developing a Zigbee product using nRF Connect SDK v2.8.0 . While reviewing the release notes for NCS v2.9.0 , we noticed two critical bug fixes related...
Hi Nordic team,
I have a question regarding the RF matching networks used in the nRF54LM20A-PAAA reference design and in the nRF7002 Expansion Board II (PCA63571).
For...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
I am new to nRF programming. My "far away goal" is to make a BLE sensor mesh with a centralised data collection.
Currently I am deciding what libraries to start playing...
Peripheral device has 2 services,but central can find only 1 service(0x1001）.
I want to find other service(0x0001)
According to the message seems to be looking for 0x1001...
Hi,
I'm using the nRF51 dongle with nRF SDK 12.3.0 and the S130 2.0.1 SoftDevice to implement a BLE central. The dongle repeatedly connects to a BLE peripheral, performs...
I'm running the PB Remote Client on a PCA10040.
I have 2 servers running on PCA10040 boards.
Watching the log whilst debugging the client, I receive the following: ...
Hello all,
I am new to nRF platfrom, I am working on a protect which contains multiple BMD-200 modules with nRF51822 controller. It has to transfer some data via UART,...
Per this blog, I understand that the nRF52's ANT pin must be matched to 50ohm via L1/C3 and that the antenna must be matched to 50ohm. Hence a trace with 50ohm characteristic...
Hello, the title is pretty descriptive.
I've tried to read through previous questions and got a rough idea but decided that it would cost too much time for me to explore...
I am working on a ble application using an nRF51822 that requires low power consumption. I'm curious if on average the observer or the central role will consume less power...
We have our own custom board using nRF52832 (via Laird BL652 module). Until recently, we have been programming our application, bootloader and softdevice using the PCA10040...
SDK12 and SD 132 v3.
I have my code working for HVX from the peripheral. I can HVX send up to 80 bytes on one characteristic in one call (ATT MTU was set to 83 and DLE...
The NRF52 product spec suggests:
"The input buffer of a GPIO pin can be disconnected from the pin to enable power savings"
I've found that gpio.h provides the function...
Here is a snippet of my debug log:
nrf_sdh_freertos: Creating a SoftDevice task.
nrf_sdh_freertos: SoftDevice task not created.
app: ERROR 4 [NRF_ERROR_NO_MEM] at ...
When using radio notifications, there are a few compiler warnings.
Compiling file: ble_radio_notification.c
../../../../nRF5_SDK_14.2.0_17b948a/components/ble/ble_radio_notification...
I've been working with an Adafruit NRF52 Feather board for the last week, and have been struggling to get the board to go into a low power mode. At the moment, I am working...
