Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi,
Thanks for taking the time looking into issue.
We are using Keil uVision 5.14.
Our target is a custom board (BMD200 eval Module based on nRF51822)
We were able to...
Hei guys,
for a new custom board based on nrf52832 where i have to minimize power:
have an external Li-Po battery, with a cutoff @3.0v, so the range will be 4.2v...
blesc_pairing_dhkey_check_failed.zip
Hello,
I used the example ble_app_multirole_lesc and paired with nRF Connect app. However I got the error message (in Bluetooth...
Hi!
So I have my GATT value of a service that I would like to update.
Sadly that value always stays at the initial value.
Below you can find my update function.
uint32_t...
I am using SDK12.0.0. ble_app_uart example, and I have change the clock to using LFCLK RC. I know from nRF51822-PAN_v3.1.pdf that we need to calibrate the LFCLK RC after reset...
I've managed to overcome all the quirks in setting up Eclipse/gcc development with the nRF52 PDK (PCA10056), and I can build the sample projects just fine. Here's my issue...
I arrived at step 8 in this tutorial
github.com/.../custom_ble_service_example
Now I'm supposed to propagate events to the application, for example connection state...
I am using a usual uart to bluetooth application and it works great, but I would like to set this application to be a known apple midi device, it seems I only have to add...
When running ble_peripheral\ble_app_uart example..... Of course I am a little bit
corrected.....
Beacons occasionally stop.
Despite the following settings:
#define...
Hi!
Is there any example app where I can find how to use L2CAP protocol on nRF52 series? Apple introduced L2CAP in iOS 11 and I want to give it a try but I can't see any...
Hello, I'm migrating a project from nrf51 S110 to nrf52840 S140, I encountered an error
"nrf_nvic_state" not found, I solved it by adding app_util_platform.c.
The problem...
Hi,
I am trying to make an empty custom service by following this tutorial from Nordic
devzone.nordicsemi.com/.../ . However I am unable to get the service to show
up...
