nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hi there,
Is it possible to use TWI0 and SPI0 (or TWI1/SPI1) time multiplexed?
When enabling them both in sdk_config.h I get "Error: L6200E... IRQHandler multiply defined...
Hi guys,
I'm having some trouble with an spi flash memory (AT45DB081D) I interfaced on my nrf51 DK.
I used the spi master code of nRF5 v.12 SDK as base. I'm using gcc...
Hi,
I try to using nrfjprog to burn softdevice + bootloader + applacation, but it shows that application burn failed.
My SDK version is nRF5_SDK_12.2.0_f012efa and...
I'm using GCC 5.3 on Windows 10 64 bit. The linker is successfully opening nfc_t4t_lib_gcc.a, but is failing with undefined references to functions declared in nfc_t4t_lib...
Hello!
I have a device with custom nrf52832 board.
This device can beep using buzzer. Frequency of the sound is generated by pwm driver from SDK. I'm changing frequencies...
Hi, i read here, that softdevice 7 has a bug and the beacon firnware drawing too much current. I measured 1mA.
So, i looked out for a precompiled set that works fine.
I...
HI:
I am created my profile(but disable some serve), but it bonging failed, and program jump to 0x0000F04C~0x0000F056 loop.
The attach file is my profile sum.
#define...
hi,I got a very strange phenomenon when our board begin a mass production.Here is some details:
1.Our board use a 4.2v lithium battery;and we have downloaded our firmware...
Hi,
I'm using nRF5_SDK_12.2.0_f012efa and s132_nrf52_3.0.0_softdevice. We want to do the OTA on it. However, I found that there is no DFU service in the HRS example.If...
Hello,
I am using the uart example with modifications to add SAADC and TWIS. It woked well for a while but now it does not connect properly to my iPhone. I reverted to the...
I am developing Timeslot program with FreeRTOS. (on nRF51822)
timeslot's signal handler is
timeslot_signal_callback()
...
xQueueSendFromISR(s_timeslot_queue, &cmd, NULL...
BT 5.0 mention that:
Up to 8x the broadcasting message capacity over Bluetooth 4.2, with
support for larger data packets: 31-octet to 255-octet packages.
Do you have...
