Hello,
I am trying to use an sdcard with the nrf54l15 DK board with the 2.9.1 sdk. However I encounter "<err> fatfs: Storage init ERROR! error: -134" when calling the disk_access_init...
I will attach my main.c and skd_conifg, maybe i'm overseeing something in code. Also i will attach schematics and pcb. I'm aware of RGB led consumption, in reality it's around...
Hi Nordic,
I am currently writing about the process of performing channel sounding sequentially on three connected devices. However, after the first channel sounding is...
I am using LVGL for simple Eink display UI, and trying to implement a simple if condition to check if the passed string argument is null as below:
If I only have btn1...
Nordic TS,
I've installed and begin to experiment with the DECT NR+ v1.1.1.0 FW. Initially, I'm noticing on obvious difference in the behavior of the dect_hello sample between...
I am trying to use the FIFO from the ADXL362 with in the Thingy:53. As I noticed there is now the Option to use ADXL362_STREAM. I just wanted to use the example from: https...
The specification for the nRF54L15 states that the typical current consumption for I_TIMER3 (TIMER10 running) is 240 mA/milliamps . The other timer values in the table are...
We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hi everyone,
I have a nrf52-DK, I made samples with the saadc unit and i noticed there are unexplained peaks.
I connected the MIC's output (its VDD is from the board)...
Hi I bought quite a few of these on boards on e-bay and have worked a lot with them.
One thing that is confusing me is the variation in the number of retries, even when...
Hi,
I have tested a sample code which sends some data through BLE in nRF52 development kit(PCA10400). The code is attached below.
nRF5_SDK_11.0.0_MPU6050_Acc_X_Output...
I'm trying to compile the bootloader_secure example for the 10040 dev board using make, and it appears the makefile was not updated correctly with the changes made to the...
Segger RTT viewer is a great debugging tool. But every time when I download new firmware into my board I have to close the viewer and then open it after download is finished...
Hi guys,
in my application, I'm trying to do multiple fota, I succeed at the first time & after that I can jump again to the bootloader, but after that something is going...
I used nRF51822 IC and SDK11 with softdevice S130. I found a problem that our product cannot work. I dumped the hex code of 2sets from 0x00000000 to 0x0003ffff. One can work...
Hi,
I am using the nRF51822 module. I am facing problem to send multiple data formats packets over nrf module. I am using nrf SDK 11 version.
I am attaching my code with...
I want to start developing a Bluetooth device with the NRF52 DK. For debugging and sniffing purposes to see what is going over the air, use the NRF51 dongle, get a NRF51 DK...
In the nRF52 specification, I cannot find figures for the interrupt latency for event on GPIO pins in different power mode OFF, ON (constant latency, Low Power).
Can you...
Hi. I need to use direct advertising option in my application to minimize the time needed to establish the connection.
Firstly, I set up the connection during "normal" fast...
Dear Nordic Team,
Thanks for supporting.
I am try to work multiple (Peripheral) tag ID read with one central and stored in my PC via UART communication. Which example...
Hi,
I am new to nRF microcontroller and communication . currently, I am working on nRF51822 microcontroller. I am able to communicate between two nRF51822 microcontrollers...
