Custom PCB with nrf5340/nrf7002. Currently was using NCS2.9.0, with WPA2-PSK connection to the wifi.
While trying to enable use of WPA2-Enterprise, I updated to NCS3.0.0...
When using the shell_module project of SDK v3.0.1, I changed uart20 to pins p2.0 and p2.2, and the serial port printed garbled text.
Below is my overlay file:
Strangely...
Beginner here .. steep learning curve for Nordic ... trying a project with I2S. Took half and hour with an ESP32, but many many hours later, no joy with Nordic.
Working...
Hello. I use the function zb_zcl_finish_and_send_packet to send data from ZC to ZED and it works but one problem is that we're using a rather slow poll (20 seconds) to enhance...
Dear Nordic DevZone,
I'm encountering pairing issues with mobile devices and a nRF54 DevKit flashed with HCI over UART firmware. After initial pairing, deleting the bonding...
Hi, i have locked my beacon with the write_lock characteristic and now i want to unlock the beacon with the lock code which is hard coded in my code. but i was unable to do...
Hi Team,
What if I don't what to use BLE stack but still want to use nRF51 Radio (PHY + MAC) to implement some custom communication protocol between multiple nRF51 devices...
i am new at this so please bare with me.
i was using a nfr51822 with s110 version 7 and i now i want to migrate it to s110 version 8.
i have made a few changes according...
After checking bootloader example from the SDK version 10, I am not able to find appropriate ROM / RAM addresses configurations for 16kb RAM chip. The Bootloader examples...
Trying to run S130 V2.0.0 with ble_app_proximity on a BLE400 motherboard.
Im getting a hang at the call to SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM, NULL...
Hi,
We just received our custom board based nRF52832, below nRF52832 schematic
I succeed to flash the board. but i have frequency troubles.
I made a simple exemple...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I have opened the nordicID sample project "InventorySample" for Windows CE in VS2008 it successfully builds the project but when i deploy it on mobile simulator Pocket PC...
Hi,
I'm using S132 v2.0.0 and nrf52832. I've got a problem when I'm trying to call any softdevice function from radio notification event handler.
#define RADIO_NOTIFICATION_IRQ_PRIORITY...
I am using nRF52832 DK and we designed a custom board using nRF52832. I am using a windows 10 lap. It used to program successfully from windows 10 lap and boards will advertise...
Hello,
I use nrf51 based device as peripheral with SD110.
I use connectable advertising ( BLE_GAP_ADV_TYPE_ADV_IND, BLE_GAP_ADV_FP_ANY ) and turned on BLE_GAP_EVT_SCAN_REQ_REPORT...
Hello,
what address in flash is it safe to store my application settings (some calibraton data) which should be preserved during application updates. I use S110 v8, dfu_dual_bank_ble_s110_pa10028...
Hi all, i'm trying to understand how to program my nrf51 DK in order to perform a temperature measurement with the onboard sensor, convert the battery voltage with the ADC...
I use dfu_dual_bank_ble_s110 bootloader from SDK10. I want the bootloader to check whether if incoming firmware is compatible with the device it is uploaded to (i.e. device...
Hi
I want to connect to only a single master device by s110. I used the example parameter setting from "ble_app_hids_keyboard" for gap_params_init, advertising_init and...
I have modified the Android Blinky App to connect two peripherals (nRF52 DK)
Scanning and Connecting to two peripherals works.. but when i want to start sending notifications...
