This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hi,
I was at the webinar today where they talked about SDK 3.0.0. They mentioned that the QSPI examples were "JESD216 flash" and "JEDEC SPI-NOR flash". I don't see either...
Hi.
We have a device connected to Azure IoT Hub with telemetry interval set to 10 min and on interupt. Tried changing interval to every hour, but then it looses connection...
We are currently utilizing the nRF5340 with Zephyr OS version 3.6.99-100befc70c74 and nRF Connect SDK version 2.7.0-5cb85570ca43. We have the following inquiries:
If we...
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board and a series of nrf52840dongles (provisioning and configuring inside the software and...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
The ble-sdk-arduino UART examples (and others?) have a rather convoluted scheme to delay the ChangeTimingRequest until after an ACI_EVT_PIPE_STATUS event indicates that the...
Hey guys,
With the BLE stack initialized, I’m not able to get the power down to where I’d expect with nRF51822, running SD S110 8.0 and SDK 9-2.
I’ve tried three, very...
Hi,
I'm new with a) the Nordic Softdevice environment and b) using the nRF52. So there are a few questions...
As a starting point I've used the template project (.....
Hello everyone ,
i am trying to increase the sound of the buzzer so can anyone suggest me do i ahve to increase the supply voltage or do i have to modify the dutycycle...
I have now used days trying to create a working clone of "dfu_dual_bank_ble_s110_pca100028" so that the source would compile and result would work correctly, independently...
I have 5 LEDs - ideally I would like to control the brightness of each one independently (i.e. 5 PWM channels). I'm using SDK 9.0 and SD 310. I have been looking at the PWM...
Hi,
I got the ble_app_beacon_s110_pca10028 from Keil_v5 Pack Installer to compile. I followed the step to use nrfutil.exe to generate a zip file. But when I did the DFU...
I can't afford nRFgo Starter kit as of now; so my question is if there any other way to program my application (firmware) in nRF8001? I am looking from following options:...
Hi,
File "nrf_drv_config.h" defines both TIMER1_CONFIG_BIT_WIDTH and TIMER2_CONFIG_BIT_WIDTH as "TIMER_BITMODE_BITMODE_16Bit", can these timers be configured as 24 bit...
HI,ALL,
I want to take use of hardware flow control, but when i set or clear the RTS signal, it failed.
something about the attempt as following:
the purpose:enable the...
Dear all,
I'm using an nrf51822 (running softdevice 6.0.0) with the proximity profile.
With iOS8, I was able to find & pair my device with the nRFproximity app.
After...
Hello from Spain!
It is my first time that I use a Bluetooth chip so I am following all your code stack and some answers of this portal, but I am having problems with the...
Hello everybody,
I am using RTC1 for time measurement, this works fine as long as no BLE communication is running.
The RTC is initialized with
const nrf_drv_rtc_t...
situation:
We are developing an nRF51 application with OTA DFU. we use SDK 9.0.0 and the DFU bootloader version is v8. We have prepared different two packages. Single OTA...
